片语

pump-body water drain泵体放水门

pump your body泅鄂茄唱狼勉茄拌绰绝绰吧

pump impeller body泵叶轮体

fuel pump body燃油泵上体

pump body bearing泵体轴承

injector pump body喷油器油泵体

pump chamber泵体；泵房；泵室

pump-body water drain valve泵体放水门

counterweight hydraulic pump body平衡重液压泵体

main pump body主泵泵体

英汉例句

• Therefore, the pump body and screw cylindrical surface and screw and screw clearance should be as small as possible.

  因此，泵体与螺桿外圆表面及螺桿与螺桿间隙应尽可能小些。

• Transparent tube and pump body of material consistent, hardness, have the same life.

  透明管和泵体的材料一致，硬度相当，具有同样的寿命。

• Particularly necessary to point out that the liquid in the pump body mass flow rate of less than the circumference of the circumferential speed of the impeller.

  需要特别指出的是，液体质点在泵体流道内的圆周速度小于叶轮的圆周速度。

• The artical presented Designing formulas of pump body and impeller and the-defining way of liquid storage chamber and air-liquid-isolating chamber of self priming type centrifugal pump.

  本文提出了有关自吸式离心泵泵体及叶轮主要尺寸的设计公式，泵体储液室、气液分离室等的确定方法。

• The relief valve can be cast and pump body and pump cover, also can separate assembly.

  安全阀可以与泵体或泵盖铸成一体，也可以单独装配。

• Marine grade aluminium pump body with Rilsan lining is a proven robust pump design for long life.

  海洋级铝泵体与丽绚衬砌是一个强有力的证明，泵的设计寿命长。

• Screw pump body and at the same time, each other between the screw and screw and form a sealed chamber, ensure airtight, otherwise there may be liquid backflow from the gap.

  同时螺桿与泵体、螺桿与螺桿间又相互形成密封腔，保证密闭，否则就可能有液体从间隙中倒流回去。

• Do not switch when starting pump: fill too tightly or between the impeller and pump body and the plug was stuck debris or shaft, bearings, minus leakage ring rust to live, or severe bending shaft.

  启动时泵不转：填料太紧或叶轮与泵体之间被杂物卡住而堵塞，或者是泵轴、轴承、减漏环锈住，或是泵轴严重弯曲。

• The nozzle body extends towards the outside of the pump body to provide a burner with supercharging oil.

  所述喷嘴体朝泵体的外部延伸，以便将增压油供至一个燃烧器。

• Crush knife installed in the pump body and impeller edged blade into the crush blade unit.

  粉碎刀安装在泵体内，与叶轮上的带刃叶片组合成粉碎刀组。

• The manufacturing process of foaming mould of an oil pump body by using LOM prototype, electroforming and wire-arc spraying was introduced in detail.

  以制造泵体发泡模具为例，详细介绍了在LOM原型的基础上，通过LOM原型的预处理、电铸和电弧喷涂等工艺手段快速制造发泡模具的过程。

• The low-carbon alloy pump body, impeller and stirrer are highly corrosion-resistant, and the pump body is sprayed with multiple layers of anti-corrosion paint externally to ensure long service life.

  泵体、叶轮、搅拌器采用低碳合金材料，具有较强抗腐蚀性，泵体表面喷涂多层防腐漆，使用寿命长。

• Ruled out: relax fill, dredge flume; disassemble pump body to remove debris, rust; Calibration shaft removed or replaced a new shaft.

  排除：放松填料，疏通引水槽；拆开泵体清除杂物、除锈；拆下泵轴校正或更换新的泵轴。

• The pump body and pump cover composes the pump studio. The inlet of the pump body is horizontally while the outlet is straight-up.

  泵体和泵盖构成泵的工作室，泵体的入口为水平方向，出口垂直向上。

• The results show that the cracking of the pump body resulted from the interaction of phase transformation and heat stress, as well as the poor quality of metallurgy.

  结果表明：泵体裂纹为相变应力和热应力以及材质冶金质量不高共同作用而产生。

• In the winter when the pump body to avoid cracking, should be more than the water tank and emptying the sprinkler pump, again when working for filling water pump.

  在冬季时为避免泵体冻裂，应将洒水车罐体内和泵内的余水排空，再次作业时则需要为泵内加注引水。

• There is no need of bottom valve in pipeline only to ensure certain priming oil in pump body before work.

  管路中不需底阀，工作前只需保证泵体内储有定量引油即可。

• Gear pumps in the pump body with a pair of rotating gears, an active and a passive, relying on two inter-meshing gears to pump cavity of the whole work in two separate parts.

  齿轮油泵在泵体中装有一对回转齿轮，一个主动，一个被动，依靠两齿轮的相互啮合，把泵内的整个工作腔分两个独立的部分。