片语

friction generated heat摩擦生热

friction n heat摩擦热

Friction means heat摩擦起热

friction axis heat摩擦热

friction generating heat摩擦生热

friction heat value油流摩擦热

friction heat power摩擦发热功率

frictional heat摩擦热

friction heat flow摩擦热流量

英汉例句

• In theory and practice, it is important to build up the heat transfer equations, compute the friction heat and temperature and determine the influences on the speed and dynamics.

  建立热传递方程，计算轴承的摩擦热和温度分布，研究轴承的热特性，及其对速度和动力学性能的影响是一个具有理论和实际意义的重要课题。

• The counterpart volume ratio influences the distribution of friction heat in dry tribological system and the dry tribological properties of materials.

  金属干摩擦副双方的相对体积比影响摩擦热在干摩擦学系统中的分配，从而影响材料的干摩擦磨损性能。

• According to conservation of energy, when Joule-Thomson effect on natural gas and friction heat of liquid are considered, a temperature drop formula to calculate multiphase pipeline is deduced.

  根据能量守恒原理，既考虑天然气的焦耳—汤姆逊效应，又考虑了液体的摩擦生热，推导出了计算多相管流温降的理论公式。

• The results show that the friction heat is obvious under high speed dry sliding;

  结果表明：在摩擦过程中，摩擦热的形成是显着的；

• In this computation, the heat convection, the heat conduction between the strip and the roller as well as the friction heat was considered.

  此计算中考虑了对流换热、过程中与带钢之间的热传导以及摩擦热。

• Plastic deformation heat and friction heat are the two principle factors which caused the temperature rise of cold rolled thin plate.

  冷轧时轧件塑性变形热和摩擦热是导致轧件温度升高的两个主要原因。

• The use of the magnetic particle clutch is limited by its heat dissipated power as a quantity of friction heat is generated when it is in the slip operating mode.

  由于磁粉离合器处于滑差工作状态时，产生大量摩擦热，从而使它的应用受其散热功率的限制。

• Plastic deformation heat and friction heat is the two principle factor which caused the temperature increment of cold rolled thin plate.

  冷轧时轧件塑性变形热和摩擦热是导致轧件温度升高的两个主要原因。

• In this paper operating and frictional conditions of floating piston pin bearings are discussed and a method for calculating their friction heat output is presented.

  本文分析了浮动式活塞销轴承工作状况及摩擦状态，提出了计算柴油机浮动式活塞销轴承发热量的方法。

• Empirical formulae were adopted to calculate friction heat and heat transfer coefficient.

  选用相关经验公式计算摩擦热及换热系数。

• Combined with the problem of the fuel flow, the friction heat model between diesel fuel and the conduit of the spray oil pump was studied by the method of conservation of energy.

  结合燃油的流动问题，采用能量守衡的方法，建立了柴油与喷油泵油道间的摩擦产热模型；

• An optimized ram speed profile fully USES the friction heat to keep the best flow characteristics, which corrects many of the fill and warpage problems.

  最适化螺桿速度充分运用摩擦热，将塑流保持在最佳状态。许多充填和翘曲的问题也就迎刃而解。

• Motorcycle, clutch operates very frequently and generates quite amount of friction heat which leads to quick wearing.

  摩托车离合器离合频繁，产生摩擦热量大，磨损快。