片语

Combined heat power generation汽电共生

waste heat power generation余热发电

heat equator generation in flow流动发热

heat equator generation热量生产

waste heat power generation technology余热发电技术

heat-generation system发热体系

waste heat power generation station余热电站

specific heat transfer generation比传热熵产

英汉例句

• The frictional heat generation and heat flow distribution of some parts of the gearbox are investigated.

  并对变速箱局部机构粘性剪切发热机理和热源热流分配进行了探讨。

• A model of comparative-oxidation method is built to calculate heat generation rates of low-temperature oxidation of coal.

  同时提出了参比氧化法的理论模型，并根据该模型推导出煤低温氧化产热速率的计算方法。

• The finite element method (FE'. I) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details.

  采用有限元分析方法对线圈匝数、电流强度、电流频率等对焦耳热产生速率的影响进行了详细的分析讨论；

• Then units can be arranged to optimize heat generation and dispersion with a direct impact on energy consumption.

  然后可以安排这些单元以通过直接影响热量消耗来优化热量的生成及散发。

• This system employs absolutely no hydraulics, and so the effects of heat generation in long-term operation are negligible resulting in stable repeat accuracy.

  液压驱动长时间工作所产生的油温的变化对于折弯精度的影响已经完全消除。

• In the compression process take away heat generation of compression.

  在压缩过程中带走压缩产生的热量。

• To reduce heat generation of the hydraulic system the main component pressure of the loader hydraulic system under different working conditions is tested, the pressure loss of each part is analyzed.

  为研究热量产生的原因，从系统上减少热量的产生，测试了装载机液压系统在不同工况下各主要元件的压力点压力，分析了各部分的压力损失情况。

• Every 148 gram potatoes heat generation is only 100 calories.

  每148克马铃薯产生的热量仅为100个卡路里。

• The result shows that the technical parameters of FSW and the heat generation in the pin are important to setting thermal models.

  结果发现，搅拌摩擦焊的焊接工艺参数、搅拌头探针产生的热量等都对温度场模型的建立起着重要作用。

• It is heat generation and resistance that brings your 「fan」 into play, keeping everything cool, and electron transfer at a controlled level.

  它使你热发电和阻力，「范」的作用，使一切清凉一、电子传递控制水平。

• Also, in order to facilitate the removal of heat generation at a location where the partition is placed, a reaction inhibition layer is disposed in that location.

  另外，为了便于除去安置隔板的位置处产生的热，在该位置安置反应抑制层。

• The increased temperature influences greatly on reliability of seal and system when shock absorber is working, the mechanism of heat generation when oil passes damping valve is analyzed.

  针对减振装置工作时温升对密封件及系统可靠性影响较大的问题，分析了油液通过阻尼阀生热的机理。

• The cool type series USES forced cooling fluid that, when passed through the nut, minimizes heat generation and thermal expansion.

  凉爽型系列采用强制冷却液，当通过螺母通过，最大限度地减少热量的产生和热膨胀。

• The paper presents the heat generation rate on the bases of measurements of the contents of uranium, thorium and potassium for different types of sedimentary rock in Tarim basin.

  通过塔里木盆地不同层系沉积巖石中放射性元素铀、钍、钾的含量实测数据，计算了不同巖石的生热率。

• In addition, the conception of parallel network resistance heat generation has been applied to deal with the non-uniform internal heat source item.

  同时用并联网格电阻发热的概念处理非均匀内热源项。

• Taken example by remaining heat generation of a petrifaction corporation, its financial feasibility is analyzed.

  以某石化公司余热发电项目为例，对余热综合利用发电的财务可行性进行了实证分析。

• In this model, the contribution of blood flow and metabolic heat generation has been included and it is not required that the tissue be initially at its phase change temperature.

  模型中包括有血流和代谢热的影响，且允许生物组织的初始温度高于其相变温度。

• The correlation of vessel distribution, blood perfusion rate and metabolic heat generation to biological 3-D temperature distribution was also discussed.

  讨论了血管形状分布，血液灌注率，代谢热与生物体三维温度场变化规律的相关性。

• Mudstone has highest heat generation comparing with siltstone and sandstone.

  其中，泥巖的生热率最高，而粉沙巖、砂巖的生热率次之。