this paper is a continuation of the author「s on point contact drive delivered at the bevel and hypoid gear meeting in 1975, which will soon be published in acta mathematicae applagatae sinica.

本文是作者1975年锥齿轮及双曲型齿轮报告会上关于点接触传动报告一文的继续；

then, according to the cutting tooth processing principle, establish hypoid gear model, and conduct virtual assembly, interference checking, provides the precise model for the following analysis.

再根据切齿加工原理，建立了準双曲面齿轮模型，并进行虚拟装配，干涉检查，为后面分析提供精确的模型。

the hypoid gear is one sort of the special bevel gears. it gets comparatively extensive application in aircraft industry, automotive industry and tractor industry.

準双曲面齿轮是一种特殊的锥齿轮，它在航空、汽车、拖拉机等工业中得到了较为广泛的应用。

an optimum design method of hypoid gear is proposed;

提出準双曲面齿轮的优化设计方法。

the hypoid gear is in common use today due mainly to the fact that the offset pinion allows the propeller shaft to be set below, (for cars) or above, (for commercial vehicles) the crown wheel center.

现在的主减速器普遍使用準双曲面圆锥齿轮，这主要是因为 主动锥齿轮的偏移允许轿车上传动轴布置得比从动锥齿轮低 一些，而商用车上又允许布置得比从动锥齿轮高一些。

a new cad/cam integration system about hypoid gear blank is introduced.

论述了準双曲面齿轮齿坯cad/cam集成系统的结构、功能及其原理。

the theory of calculating geometric parameters of pitch cone of curved tooth hypoid gear is investigated in this paper.

本文研究了曲齿準双曲面齿轮分度锥面几何参数计算的原理。

the intelligent check system proposed in this paper can be used as the final quality check and quality control tool in spiral bevel and hypoid gear manufacture process.

本文提出的锥齿轮智能检测系统可在锥齿轮制造过程中用作最终质量检测和质量控制工具。

by using the tooth edge contact analysis and finite element method, the maximal stretched stress, maximal compressed stress and tooth surface contact stress of the hypoid gear are analyzed.

利用有限元和边缘接触分析方法，讨论了上述方法设计出的齿轮副齿根最大拉伸应力、齿根最大压缩应力以及齿面接触应力的变化；

based on the conceptual model of the five-axis simultaneous cnc bevel gear cutting machine, a new machining theory for the function-oriented active tooth surface of hypoid gear is proposed.

基于五轴联动数控铣齿机的概念模型，提出一种新的加工準双曲面齿轮主动设计齿面的切齿原理。

an optimization design method for a hypoid gear with high tooth was proposed based on the investigations into variations of working tooth height and constraint conditions of undercut.

通过增加工作齿高和对根切条件的深入研究，提出了高齿準双曲面齿轮的优化设计方法。

the integral type housing, hypoid gear design has the centerline of the pinion set above the centerline of the ring gear.

集成型的差速室、準双曲面齿轮的设计中，小齿轮组中心线在环形齿轮的中心线之上。

the vibration of hypoid gear is main reason of rear axle vibration, the key of reduce rear axle vibration lie in improving gear」s processing, assembly quality.

準双曲面齿轮的振动是后桥振动的主要原因，减小后桥振动的关键在于提高齿轮的加工，装配质量。

compared to bevel gear, hypoid gear has larger overlap coefficient, lower gear contact stress, more smooth transmission, lower impact and noise, higher load bearing capacity, longer life and so on.

準双曲面齿轮与普通圆锥齿轮相比，具有重合度大、齿面接触应力低、传动平稳、沖击和噪音小、承载能力高和寿命长等优点。

by processing and analysis of test data, influence degree of different factors is obtained, and the optimum formulation of high-duty hypoid gear lubricant of automotive drive shafts is obtained too.

通过对试验数据的处理和分析，得出各因素对试验指标的影响程度，并获得了满足在给定工况条件下的汽车驱动桥双曲线齿轮油的最佳配方方案。

the active design technique of hypoid gear tooth face provides a kind of fresh method of the hypoid gear design.

準双曲面齿轮齿面主动设计技术为準双曲面齿轮副的设计提供了一种全新的思路。

in particular the automotive industry is developing rapidly so that the requirement of meshing quality of hypoid gear is increasing.

特别是汽车工业的迅猛发展，对準双曲面齿轮的啮合质量要求越来越高。

thus, the basis of founding loaded tooth contact analysis calculating method of hypoid gear is brought about.

其结论是建立该类齿轮副承载啮合性能分析计算方法的基础。