片语

junction-temperature measuremeat结温测量

IGBT junction temperatureIGBT结温

LED junction temperature结温

junction n temperature接点温度

single junction temperature sensor[自]

pn junction temperature sensingpn结测温

maximum junction temperature最高结温度

junction temperature distribution结温分布

英汉例句

• In the junction temperature measurements, we get reasonable curves and also confirm the accuracy of the system's measurements further.

  在接面温度量测上，我们得到了合理的曲线，也进一步地确定系统量测的準确度。

• To make accurate temperature measurements with thermocouples, the reference junction temperature must remain constant. If it varies, suitable compensation for these variations must be provided.

  要用热电偶实现精确的温度测量，参考端温度必须保持恒定；如果会变化，必须提供这些变化的适当补偿。

• The junction temperature (TJ) can be determined using the thermal diode in the processor core.

  使用处理器器核心中的热敏二极管可以判断交叉点温度(TJ)。

• This paper presents a well water temperature monitor, and its use of PN junction temperature sensor as temperature components, integrated circuits used for ICL7126 and other A / D converter.

  本文介绍一种井中水温监测仪，其采用PN结温度传感器作为感温元件，用集成电路ICL7126等作A/D转换器。

• This paper analyzes the failure mechanism of semiconductor P N junction temperature sensors and presents a new design to reduce the internal stresses and methods to improve the processes.

  通过失效形式，分析了半导体P-N结温度传感器的失效机理，介绍了为降低内应力而进行的设计和工艺改进。

• In addition, Thermal Force-Directed Placement Algorithm is used, detailed analysis of the device optimized layout of the component junction temperature and the average PCB temperature are shown.

  另外，本文还运用热力导向优化算法，分析了电子元器件的优化布局对元器件的结点温度的影响。

• PN junction temperature sensor is used. 16 temperature signs are acquired at the same time. Proceeded data can be indicated, printed or controlled.

  系统选用PN结温度传感器，可同时测取16个温度信号，经数据处理后可实时显示、打印或控制。

• Moreover, we design our owned unique heat sink to sure our junction temperature is lower than 45 degree.

  此外，我们设计我们拥有独特的散热片，以确保我们的交界处的温度低于45度。

• A method for measuring and controlling the junction temperature of power transistor during succession operation life test is proposed.

  为了在试验周期中了解晶体管的结温，提出一种在功率晶体管稳态工作寿命试验过程中结温的测量与控制方法。

• There are two limitations on the power handling ability of a transistor: average junction temperature and second breakdown.

  有两个限制了晶体管的处理能力，功耗：平均交界处的温度和二次击穿。

• Transistor thermal spectrum, as a new method, different from the commonly infrared thermogram, is introduced to characterize the non-uniform property of the junction temperature distribution.

  晶体管热谱是表示晶体管结温不均匀性的一种与热像图不同的新方法。

• A method of thermocouple cold junction temperature real time compensation was introduced, which utilizes digital sensor to measure temperature, and micro-controller to process the temperature data.

  介绍采用数字温度传感器进行冷端测温，微控制器进行计算处理，对热电偶温度实时修正的方法。

• The maximum acceptable junction temperature is different for C and I grade devices. If it is higher than the max. acceptable temperature, you may consider adding a heatsink or cooling fan.

  C和I级器件允许的最高接合温度不同。如果温度高于允许的最高值，可能需要增加散热片或风扇。

• When a transistor dissipates power on work, its junction temperature distribution is commonly non-uniform.

  晶体管在耗散功率时，结温分布一般不均匀。

• We also analyzed the relationship between the junction temperature with LED heat power and the convection coefficient.

  然后重分析了LED发热功率和对流交换系数对LED结温的影响。