片语

leakage conduction current漏泄传导电流

leakage e current monitor漏泄电流监测器

Leakage pulse current泄漏脉沖电流

leakage of current电流漏泄

leakage resistance current泄漏电阻电流

rated leakage operating current额定漏电动作电流

nominal leakage action current额定漏电动作电流

leakage electric current漏电电流

leakage e current漏泄电流

英汉例句

• the system has been implemented in the laboratory and proved to be a successful-designed tool for insulator leakage current monitoring.

  实验室的应用证实，该系统的设计比较成功，是一套研究绝缘子泄漏电流的有效工具。

• leakage current is another source of measurement interference that must be characterized.

  漏泄电流是另一种必须表征的测量干扰源。

• electrical characteristics: capacitance, dielectric loss tangent, leakage current and etc. , which are specified in catalogue or alternate product specification.

  电性能：电容量、损耗角正切、漏电流等，具体数据参见产品目录和相关产品规格书。

• to perform the leakage current test, source a specified reverse voltage, then measure the resulting leakage current.

  通过施加规定的反向电压，然后测量产生的漏泄电流，即可完成漏流测试。

• the effect of aging voltage on the capacitance and leakage current of al electrolytic capacitors.

  老练电压对铝电解电容器容量和漏电流的影响。

• to ensure low leakage current and low dielectric absorption, the feed back capacitor should be made of a suitable dielectric material such as poly styrene, polypropylene, or teflon.

  为了保证低泄漏电流和低介电吸收，反馈电容器应当由合适的介电材料（如聚苯乙烯、聚丙烯或聚四氟乙烯）制成。

• some of these applications may include leakage current of capacitors, reverse diode leakage, or insulation resistance of cables or films.

  这类应用可能包括电容器的漏电流、二极管反向漏电、电缆或薄膜的绝缘电阻等。

• an usb interface based portable monitoring system for insulator leakage current is developed in order to solve the limitation of existing ways of insulator leakage current monitoring.

  针对现有绝缘子泄漏电流检测方法存在的局限性，开发了一种基于u sb接口的便携式绝缘子泄漏电流检测系统。

• since the leakage current through the zener diodes results in a voltage drop across the resistor, low leakage zener devices are desirable.

  由于流过齐纳二极管的泄漏电流会在电阻器上产生电压降，所以希望使用低漏电的齐纳二极管。

• the leakage current can be determined by applying a known voltage and measuring the current between either path to ground or path to path.

  通过施加一个已知的电压，然后测量通路至地或通路至通路的电流，即可确定漏泄电流。

• guarding may also be necessary to prevent leakage current due to test fixturing.

  保护对避免由测试夹具产生的泄漏电流也是必要的。

• in other cases, leakage may be expressed as a leakage current at a given voltage, usually the operating voltage.

  在另一些情况下，漏电可以用给定电压（通常为工作电压）下的泄漏电流来表示。

• interferences due to leakage current can be controlled by guarding as described in section 2.3.1.

  采用第2.3.1节介绍的保护技术可以控制泄漏电流的影响。

• this generates a transient current that will gradually decay to a steady value, which is the leakage current of the system for that particular path.

  这会产生一个瞬变电流，并逐渐衰减至一个稳定值，这就是特定通路的系统漏流。

• one measure of the quality of a diode is its leakage current at a specified reverse bias voltage.

  衡量二极管质量的一个方面就是在规定的反向偏置电压下的泄漏电流。

• when measuring the leakage current with this setup, the voltage bias is applied to all the diodes simultaneously through the normally closed contact of each relay.

  当利用这一配置测量漏流时，通过每个继电器的常闭触点同时向所有的二极管施加偏压。

• after cleaning the winding end, the leakage current becomes normal.

  清除绕组端部污秽后，泄漏电流正常。

• as shown in diagram 1, as from the voltage uc, the leakage current increases very swiftly and the breakdown voltage is reached for value ue.

  正如图1所示，而从电压uc开始，漏电电流迅速增加，击穿电压达到ue。

• a leakage current will flow around this loop, but won「t affect the measurement.

  泄漏电流将在此回路中流动，但是不影响测量。

• the guard can be used to isolate the high impedance input lead of the ammeter from leakage current due to voltage sources.

  保护可以用来把安培计的高阻输入引线和由电压源引起的泄漏电流隔离开来。

• once the leakage current in a given pathway is known and remains consistent, it can be subtracted from subsequent measurements.

  一旦知道了给定通路的漏流，并保持稳定，即可从随后的测量值中减去该值。

• fn tunneling and hot hole (hh) stress induced leakage current (silc) transient characteristics in thin gate oxide are investigated.

  分别研究了fn隧穿应力和热空穴（hh）应力导致的薄栅氧化层漏电流瞬态特性。

• however, offset current and leakage current are the types of interference most frequently encountered and are explained further at the end of this section.

  然而，偏移电流和漏泄电流是最常见的干扰类型，并在这部分末尾进行了更详尽的说明。

• the leakage current will decay exponentially with time, so it」s usually necessary to apply the voltage for a known period (the 「soak」 time) before measuring the current.

  泄漏电流随时间呈指数衰减，所以通常需要在一个已知的时间期间内施加电压（浸润时间），然后再测量电流。

• to determine the leakage current at a particular voltage, apply a step voltage of this magnitude to the circuit.

  为了确定特定电压下的漏流，可以向该电路施加一个该幅值的阶跃电压。

• medical or low leakage current requirements compact design electronic equipment.

  医疗或低漏电流需求，集成设计电子设备。