片语

leakage gas flow泄漏气体流量

air leakage seepage flow漏风渗流

leakage e flow漏泄

leakage oil flow漏油流量

aerial drainage泄流

leaking漏，泄露，渗漏；漏出，渗入；泄露，透露（秘密），走漏（leak 的现在分词）

tip-leakage flow顶部泄漏流量

sodium leakage flow钠漏流

Leakage Magnetic Flow Detection漏磁探伤

leakage air flow rate渗漏风量

leakage magnetic flow detector漏磁探伤仪

英汉例句

• Under high frequency usage condition, the internal leakage flow rate of the piston is almost near zero condition.

  在高频使用状态下，活塞的内泄漏量几乎接近于零状态。

• The second part studies and analyzes the tip leakage flow and tip vortex.

  第二部分对叶顶间隙泄漏流动和叶尖涡进行了研究分析。

• Abstr: The leakage flow particle sensor is a new detecting automobile exhaust particles content device.

  文章摘要：漏电流式颗粒物传感器目前是一种新型检测汽车废气颗粒物含量装置。

• Tip leakage flow in a compressor which designed by use of Computer Aided design System was investigated by numerical method, for different tip leakage at design flow conditions.

  采用离心压气机计算机辅助设计系统，设计了一个离心压气机叶轮，对这一叶轮在不同叶尖间隙下内部流场进行了数值计算。

• It was revealed that the effect of depth of a honeycomb seal cell on the leakage flow did not exhibit a linear relationship.

  实验研究了蜂窝密封的泄漏特性，发现蜂窝深度对漏气量的影响并不呈线性的规律。

• The leakage flow and total temperature increase characteristics of a honeycomb labyrinth seal used in a typical gas turbine were numerically investigated and compared with a smooth labyrinth seal.

  详细介绍了三种典型阻尼密封技术袋型阻尼密封、蜂窝阻尼密封和孔型阻尼密封的结构特点、动力学特性和阻尼机理及研究和应用现状。

• Based on predecessor's work, we have modified the mathematical model for leakage flow in power steering pump.

  在前人研究工作的基础上，建立了转向泵漏油流量的数学模型。

• The results showed that the main flow rolled up the leakage flow of the tip clearance and generated the tip leakage vortex.

  结果表明：叶顶间隙气流与主流发生卷吸而生成泄漏涡。

• In this paper, the influence of tip leakage flow on the 3-d viscous flow field is investigated for different blade tip gap shapes under the condition of rotating hub or stationary hub.

  本文针对几种不同形态的叶栅顶部间隙，在环壁转动与静止的不同情况下，研究间隙内的泄漏流动对三维粘性流场的影响。

• The Basic structures of finger seal were introduced, and according to the features of finger seal structure, the mathematic model and calculating model of finger seal leakage flow were set up.

  介绍了指尖密封的基本结构，并根据指尖密封的结构特点，提出了指尖密封泄漏流动的数学模型和计算模型。

• Upstream stator-rotor interaction reduces the double leakage flow intensity in the rotor tip region.

  上游静叶干涉减少了动叶顶部二次泄漏流强度。

• More than 5000 hours test showed that the advanced design is superior to the former ones. The leakage flow is fairly stable with the change of the temperature of injection water.

  经5000多小时试验表明，改进结构比其他两组密封部件的性能优越，当注入水温度变化时，泄漏量相当稳定。

• The intensity of rotor wakes was reduced, flow separation on rotor suction side was suppressed and the tip leakage flow was suppressed periodically.

  动叶尾迹强度明显减弱，叶背流动分离得到抑制，叶尖泄漏涡也得到了周期性的抑制。

• The results show that the tip leakage flow vortex has a great effect on the blade aeroelastical stability and large tip leakage vorticity may restrain blade flutter.

  计算结果表明，漏流涡对叶片气弹稳定性影响较大，大涡量的漏流涡能抑制叶片颤振发生。