英语释义

1. a device (as a gland with packing) for preventing the escape or entrance of oil

片语

oil-seal torque油封阻力矩

double oil path seal双油路密封

oil tight油封

Oil Hub Seal芫华实业有限公司

oil filter seal滤油器密封

Oil pan seal机油盘密封条

Oil shaft seal油轴封

oil l seal油封

grease seal[机] 油封；黄油密封

oil cooler seal机油冷却器密封

oil film seal油膜密封

英汉例句

• block in the mud with four skeleton oil seal and sleeve to prevent shaft wear and prolong the service life of shaft.

  泥浆泵座中装有四只骨架油封和轴套，防备轴磨损，延伸轴的应用寿命。

• the fabrication principle of textile was analysed by anatomising the imported textile rubber oil seal sample, a new fabrication technics of textile was put forward.

  通过解剖进口夹布油封的截面，分析其夹布成型的机制，提出一种夹布制作的新工艺；通过一系列的试验，证明了这种工艺的原理和可行性。

• speedometer cable comp , clutch, brake cable comp, throttle cable comp, turning cable assy, oil seal steel wire, bearing, rubber and other wearing parts.

  咪表线、离合器、剎车线、油门线、转速线、风门线、油封、钢丝、轴承、橡胶件等易损件。

• cartridge type air and oil seals-seal air is injected into the oil seal and is vented to atmosphere between the seals.

  套筒式气封和油封总成，油封之间通密封空气，油封与气封之间有一通大气的腔室。

• the structure and application of three types of dry gas containers, such as watery oil seal, dry oil seal and rolling shade seal were summarized.

  总结了稀油密封型、干油密封型和卷帘密封型三种干式气柜的结构特点和应用情况。

• if the leakage occurs at the rear oil seal area, refer to the section, inspection for rear seal area leak.

  如果泄漏发生在后机油密封区，参看「后机油密封区泄漏的检查」一节。

• the oil pump drive gear oil seal is damaged, the air into the hydraulic system;

  油泵主动齿轮油封损坏，空气进入液压系统；

• this paper shows the construction of hydrodynamic oil seal sr. and discusses its properties and service life through test.

  本文介绍「sr」流体动力油封的结构，通过试验更进一步论述「sr」流体动力油封的密封性能和使用寿命。

• the material of oil seal is advance, reasonable, and the processing of confect is preciseness. the change of pull intension rate is small. it suit varies of abominable environment.

  因油封胶料配方先进、合理、配制过程严谨、拉伸强度变化率小，能适应各种恶劣的变化环境。

• design of mold and research of process for polyurethane elastomer for oil seal are introduced.

  介绍聚氨酯弹性体油封的注射模具的设计及工艺研究。

• power take - off, squared shaft drive. two stud flange without oil seal gasket.

  动力启动方轴传动装置。销法兰。无油密封垫圈。

• according to the international informations and santana engine, the seal mechanism and effective factors of valve stem oil seal is analyzed in this paper.

  本文根据国外资料并结合桑塔纳汽车发动机，分析了气门桿油封的密封性机理及影响因素。

• found oil seal leakage, the first shall determine the parts of the leak, if not oil seal leakage, sometimes is hard because such as the oil leakage for reasons other than and mistaken for leakage.

  发现油封泄漏时，首先应确定发生泄漏的部位，如果不是油封泄漏，有时是由于附着了油脂等泄漏以外的原因而误认为是泄漏。

• the process of typical metal insert of oil seal was analyzed, and the composite die was used to form this kind of part. meanwhile, its structure and working principle were also der demonstrated.

  通过对典型的油封骨架进行工艺分析，采用复合模对骨架加工成形的工艺，并详细说明了此复合模的结构及工作原理。

• demolition sealed block : block compress sealed under screw nut and gently unloaded sealed block (note: not to destroy the rubber oil seal seat) and cleaning.

  拆密封座：拧下密封座压紧螺母，轻轻卸下密封座（注意：不要弄破座上橡胶油封）并清洗。

• with the increase of the difference in lip and shaft diameter, the maximum contact pressure has a trend of increase by degrees, the increscent scope of the small oil seal are more remarkable.

  增大唇部过盈量，最大接触压力也随之而呈递增趋势，同样小尺寸油封递增幅度要大于大尺寸油封。

• this paper describes the tests of oil seal stock formulation and their basic performance, for some types of acm made iu american and japan.

  本文主要对美国和日本的几种型号的acm油封胶料进行了配方设计以及基本性能测试和比较试验；

• the servomechanism of guarding leak for the test of high pressure oil seal was developed, and its structure was introduced.

  开发了高压油封实验时防泄漏自动控制装置，并介绍了其结构。