英语释义

1. a ring (as of synthetic rubber) used as a gasket

片语

Sulzer gripper booster O-rings苏尔寿增压器O型圈

Elastomeric O-rings弹性O型圈

Fluid power systems-O-rings目录或摘要

O-rings housingsO型密封圈装配槽

PU O-rings聚氨酯O型圈

Elastomer O-Rings Damper型圈阻尼器

number of O-rings密封圈数量

Rubber O-rings橡胶制环形密封圈

英汉例句

• NBR rubber O-rings provide trouble-free operation at standard temperature ranges. For high and low temperature applications Viton or Silicone.

  在常温工作条件下使用丁晴橡胶，在高温或低温时采用氟橡胶或硅橡胶。

• For both O-rings and foam, that first decision was a turning point.

  对O型密封圈和泡沫，这个第一次决定都是转折点。

• Back-up rings are not seals themselves, but are usually used in conjunction with O-rings in high-pressure applications.

  备份环本身不是密封件，通常在高压应用中与O型圈配套使用。

• Wiring connection issues and leaking O-rings are among the most common causes of perforating gun misruns.

  电缆连接问题和O形圈泄露是导致射孔枪入井失败最常见的原因。

• Theoretical results showed that EORD, using general elastomer O-rings with loss-factor between 0.1 and 0.4, was enough to reduce first critical response vibrations of the experimental rotor system.

  理论分析表明，采用损耗因子在0.1至0.4之间的常用的橡胶O型圈，即可极大地降低一阶临界振动响应。

• To study the influence of O-rings secondary seals, deformation behaviors of mechanical seal faces were analyzed under different pressures with the method of integral contact analysis by FEM.

  采用整体接触有限单元法，考虑「O」型辅助密封圈的影响，计算了不同压力下机械密封端面变形行为。

• The machines used to mould, finish and check its O-rings are made in continental Europe, so have become dearer just when the firm is expanding.

  用来浇铸，完成以及检查O型环的机械由欧洲大陆国家制造；如此一来，当公司规模扩大时，进口这些设备就需要投入更多的资金。

• Gasket system is made of double-layered, closed cellular neoprene, with stainless steel O-rings for attaching gloves.

  衬垫系统由双层密闭氯丁橡胶组成，带有不锈钢O型环以附带在手套箱上。

• PTFE seats backed up with O-rings reduce the wear and tear of repeated cycling.

  聚四氟乙烯阀座备使O形圈减少磨损，反复循环。

• The WTC which was included, there were also two rubber O-rings for the end caps.

  世贸中心，其中被列入，但也有两个橡胶O型圈为端盖。

• All of the attachment holes are chamfered on the inside edges to prevent damaging the O-rings during installation of the nozzle and bulkhead see Eng.

  所有的实习孔倒角对内部的优势，以防止破坏O型环在安装过程中的喷嘴和舱壁见工程。

• Rational matching of O-rings and O-ring grooves is of great importance to prolonging the service life of O-rings.

  形密封圈和密封圈槽尺寸的合理匹配是延长密封圈无泄漏密封寿命的必要保证。

• The firm is not just an ideas factory: the O-rings are manufactured on-site, too.

  该公司并非仅是一家点子公司：它还现场制作O型环。

• Replace O-rings as required.

  按需要、更换O型密封圈。