英语释义

1. to mix before use

2. a mixture of ingredients designed to be mixed with other ingredients before use

片语

Premixing nutrient营养素预混料

premixing flour预混粉

premixing pumping预拌泵送

gas premixing燃气预混

Premixing unit预混单元

premixing plant预拌工厂

cold premixing冷预混

Batch premixing批处理预混

英汉例句

• this paper presents a new method of detecting whole premixing combustion air-gas ratio, describes the principles and operational steps of the method, and analyzes its application prospect.

  文章提出了一种全新的检测全预混燃烧空燃比的方法，并阐述了该方法的原理和操作步骤，分析了这种新方法的应用前景。

• one composition enters the static mixer after metering through high-accurate and medium-low-pressure metering pump and goes into the premixing bank for cycling.

  某一组分经高精度、中低压的计量泵计量进入静态混合器，并进入预混料罐循环；

• the results show that the premixing process improved the polyester sizing efficiency.

  结果表明，预混合工艺能提高聚酯树脂的施胶效率。

• premixing is one of the effective techniques for manufacturing composites with thermoplastic matrix.

  预混技术是热塑性树脂基复合材料制备的一项十分有效的技术。

• the invention relates to an insertable pre-drilled swirl vane for a premixing fuel nozzle.

  本发明涉及用于预混合燃料喷嘴的可插入的预鉆孔的旋流叶片。

• the results obtained by premixing palladiummagnesium with the sample solution were lower than those by standard addition method due to the precipitation of metallic palladium in the iodide solution.

  用预混合钯-硝酸镁和样品溶液，由于在碘化物溶液中易析出金属钯而使测定结果降低。

• on the basis of successful design, a new low pressure premixing rtm machine has been developed.

  在成功地设计出低压预混一次注射rtm机的基础上，又研制了新型低压预混rtm 注射机。

• its injecting time depends on volume of the premixing tank, solving ratio of carbon dioxide and composition as well as mass flowrate of carbon dioxide.

  二氧化碳注入时间取决于预混料罐的容积、二氧化碳与组分的溶解比及二氧化碳的质量流量。

• we also investigated the mechanism of the premixing process and describe a new wet-end process that shows improved physical properties.

  另外，还研究了预混合工艺的机理并且介绍了一种新的湿部工艺，这种工艺能提高纸张的物理性能。

• the air and gas premixing ability is tested with the burny experimentation about the low-pressure hot gas, and which is compared with the combustion using diesel oil.

  热态点火实验考察了同轴射流燃烧器与同轴旋转交叉射流燃烧器的预混性能，并同轻柴油燃烧情况进行比较。

• the hydrous ethanol steam was burned or mix-burned on a gasoline or diesel engine with the intake premixing method.

  采用进气道预混合方式，在汽油机（柴油机）上燃用含水乙醇蒸气或者掺烧含水乙醇蒸气。

• this device mainly consists of uniquely designed premixing chamber, purifying chamber and high effective dehumidifier.

  该设备主要由设计独特的预混室、凈化室和高效除湿机构组成。

• by the experimental bench of bluff body flame and under different working orders, the speed in blowing out the flame of methane premixing gas with vapour is measured.

  利用钝体稳定火焰实验台，在不同工况下，测量了含水蒸汽的甲烷预混气的火焰吹熄速度。

• premixing enzymes and calcium salt to manufacture bread additive, and its ash content was tested result in coefficient of variability. this coefficient could reflect mixed degree of uniformity o…

  采用酶制剂与钙盐预混合配制面包添加剂，测定灰分含量，其变异系数能反映酶制剂混合均匀度。

• the results showed that the blending method of premixing masterbatch of short polyester fiber and epdm, and then blending with pp was the best method.

  结果表明，预先将聚脂短纤维和epdm混炼制成母炼胶，然后再与pp共混进行动态硫化制备的复合材料的性能最佳。

• the paper introduces the experimental system and process of rust removal of inner wall of steel tube by use premixing abrasive jet.

  介绍了前混合磨料射流用于钢管内壁除锈的试验系统以及试领情况。

• vane number and swirl angle of a swirler, premixing distance, air velocity and fuel injection methods, etc, have remarkable effects on air-fuel mixture uniformity.

  旋流器的叶片数和旋流角、预混管长度、气流速度、喷油方式等对油气混合均匀性均有比较显着的影响；

• the air and gas premixing ability was tested with the burny experimentation about low-pressure hot gas in the production field, and finally, which was compared with the combustion using diesel oil.

  在生产现场的低压热脏煤气燃烧实验中，考察了燃烧器的预混性能，并同轻柴油的燃烧情况进行比较。

• the physical model and mathematical model of casing-cutting using premixing abrasive water jet are presented.

  基于能量原理，建立了前混式磨料水射流切割套管的物理模型和数学模型。

• this investigation of the mechanism of premixing alum-rosin size for neutral-alkaline papermaking process focused on the mixture solution charge and particle size distribution.

  中堿性造纸过程中松香明矾预混和过程的研究主要集中在混和液的电荷及粒度分布。

• the general locations of the fuel ducts are dependent on the position of the air cyclone, and long enough premixing segment should be set.

  燃料导管的位置一般视空气旋流器的位置而定，并应留有足够长的预混段。

• the hydraulics and abrasive parameters of premixing jet has great effect on casing cutting efficiency.

  水力参数和磨料参数对前混式磨料射流切割套管的效率有着极重要的影响。