片语

spiral-wound electrode螺旋状焊丝

spiral-wound heat exchanger缠绕管式换热器

spiral-wound electrodes卷绕电极

spiral-wound module螺旋缠绕模块

spiral-wound membrane technology卷式膜技术

spiral-wound tube螺旋管圈水冷壁

spiral-wound case螺旋缠绕式壳体

英汉例句

• The seal principle and its constriction of H-type complex gasket were introduced, as compared with wave-toothed compound gasket and spiral wound gasket.

  介绍了H型复合垫片的密封机理和结构，并且与波齿垫片和缠绕垫片的密封性能进行了比较。

• It is proved through test of nation akl technical standards that the spiral wound gaskets made by the plant can meet or exceed the technical requirements of the national and foreign standards.

  生产出的缠绕垫片经过各项国家技术标準测试，其外观质量和内在质量均达到或超过国内外标準技术要示。

• Valves in these classes are also available with spiral wound gasket bonnet joints when specified.

  如果需要，这种压力等级的阀门也可配置螺旋盘绕或环连接垫圈。

• In this paper, the relations between the parameters of the spiral wound paper tubes and between the diameter of the pulleys and the maximum outer diameter of the paper tubes have been studied.

  本文研究了螺旋纸管(罐身)各参数之间，以及皮带轮直径和最大纸管外径之间的关系。

• TD-SW700Spiral-Wound gasket is formed of V-shaped metallic stripe and soft non-metallic filler by means of piled, spiral wound and connected its end and beginning by dot welded.

  SW700金属缠绕垫片由V形或W形不锈钢带和非金属填充料叠合，螺旋卷绕，始末端点焊而成。

• The controlling principle of process technology parameters is expounded. The influence of the structure and technology parameters on the quality of spiral wound gaskets is investigated.

  简述了缠绕式垫片生产过程中工艺参数的控制原理，结构和工艺参数对产品质量的影响。

• Meanwhile the performance of graphite spiral wound gasket under different technique parameters was analysed.

  同时对不同工艺参数下的石墨缠绕垫片性能进行分析。

• The sealing design criteria to measure the factors of spiral wound gasket were adopted, based on this bolt loads of flange can be determined by using the new PVRC method.

  采用密封设计準则，通过试验确定了金属缠绕式垫片的垫片系数，在此基础上，按照PVRC新方法对法兰螺栓载荷进行了计算。

• In such cases, can switch to spiral wound gasket, 「o」 ring and so on, are now a number of factories he already adopted.

  遇到这种情况，可改用缠绕垫片，「O」形环等，现在许多厂已采用。

• Valves in these classes are also available with spiral wound or ring joint gaskets when specified.

  如果用户要求，这些压力等级的阀门也可提供螺旋盘绕或环连接垫圈。

• The device comprises a spiral wound element (50) within the housing that receives and coils said strip of blisters that have been breached.

  所述装置包括位于所述外壳内的螺旋卷绕元件（50），该元件收纳并盘卷已被打开的泡囊条带。

• The design of gasketed joints is critical for low-emission applications. For better control and elimination of unwinding of spiral wound gaskets, a fully-enclosed gasket cavity is desirable.

  对于低污染排放应用来说，垫圈连接设计是关键性的。为了更好的控制和防止螺旋式垫圈的退绕作用，需要配置完全包装的垫圈腔。