片语

squeeze casting process挤压铸造

squeeze casting technical parameters挤压铸造工艺参数

squeeze casting mould挤铸模

squeeze casting parameters挤压铸造工艺参数

indirect squeeze casting接挤压铸造

squeeze exhaust casting process加压排气

squeeze-casting technique挤压铸造法

squeeze casting die高压铸造

英汉例句

• the effects of two patterns of squeeze casting on mechanical properties of za43 alloy were investigated through the analysis of alloy liquid flow and pressure loss.

  从合金液的流动和压力损失的角度，研究了两种挤压铸造方式对za43合金力学性能的影响。

• aiming at the various defects in production, the effects of squeeze casting process parameters on az81 as-cast microstructure were investigated from formation mechanism and influence factors aspect.

  针对试生产过程中铸件产生的各类缺陷，从其形成机理和影响因素方面进行分析，研究挤压铸造各工艺参数对az81镁合金的铸造组织的影响。

• in this paper, the effects of pressurizing value on aluminum alloy crystal structure and the mechanical properties in squeeze casting process have been studied.

  本文研究了挤压铸造时不同加压压力对铝合金结晶组织和机械性能的影响。

• the rule for shrinkage of squeeze casting is verified in the example of al si alloy.

  本文以铝硅合金为例，对挤压铸造的无缩孔判据进行验证。

• general technique of squeeze casting has been described of which the direct and indirect processes and development and application have been included.

  综述了挤压铸造技术的概况。主要介绍了直接挤压铸造工艺和间接挤压工艺的现状、发展和应用情况。

• squeeze casting of an ly12 (2024) alloy was carried out to investigate the effect of applied pressure and followed diffusion annealing on microsegregation in the alloy.

  研究了ly12合金在挤压铸造中不同压力以及后续扩散退火制度对铸锭微观偏析的影响。

• all these results indicate the feasibility of the designed electromagnetic transfer system, the designed die structure, and the parameters of the indirect squeeze casting process.

  试制结果表明：所设计的传输管道的结构、支架挤压铸造模具设计和电磁充型间接挤压铸造成形工艺参数合理。

• influence of technology parameters and fluid flow pattern on quality of castings were analyzed. the brake pump products of vertical squeeze casting were good in qualities and low in cost.

  采用立式挤压铸造工艺，产品能以较高的质量、较低的成本满足使用要求。

• the fundamental problems of cup-shaped za27 alloy squeeze casting with high ratio of height to thickness were studied in this paper.

  本文主要研究了大高厚比za27合金杯形铸件挤压铸造过程的若干基本问题。

• indirect squeeze casting technology for bearing holder is studied.

  研究了轴承保持器的间接挤压铸造工艺；

• in the direct squeeze casting process, the influence of the process parameters and heat treatment on the mechanical properties of az91d alloy is studied.

  采用直接挤压铸造成形工艺，研究了挤压铸造工艺参数和热处理对az91d合金力学性能的影响。

• a set of squeeze casting mold was designed for fabrication of complex water-soluble salt core.

  设计了一套用于制备复杂形状水溶性盐芯的挤压铸造模具。

• the principle and processing characteristics of semi-solid squeeze casting were introduced briefly;

  简要介绍了半固态挤压铸造原理与工艺特点；

• the distinct characteristic of squeeze casting with larger ratio of height to diameter is (heterogenous) distribution of squeeze pressure.

  大高径比挤压铸件成形时的一个显着特征是压力沿着轴向分布严重不均。

• two dimensional carbon fiber fabric reinforced magnesium matrix composites were prepared by squeeze casting technology, and their basic properties were studied.

  采用挤压铸造法制备出二维碳纤维织物增强镁基复合材料，并对其基本性能进行了研究。

• the influence of squeeze casting technique on mechanical properties and microstructure of bar-shaped za27 alloy was investigated.

  分析了挤压铸造工艺对棒状za27合金力学性能及组织的影响。

• squeeze casting is an advanced liquid formation technique for machine parts, and has the advantages of high adaptability, high efficiency, high mechanization degree and good work condition.

  挤压铸造是一种先进的机械零件液态成形技术，具有工艺适用性好、工艺出品率高、机械化程度高、生产率高、劳动条件较好等优点。

• a set of complete technological system and theoretical basis has been established for squeeze casting technology during period of the past 60 years.

  挤压铸造问世60年，已建立起自己完整的工艺体系和理论基础，在国内外形成年产10万t以上铸件的批生产能力。

• the fundamental problems of za27 alloy squeeze casting with high ratio of height to thickness were studied in this paper.

  本文主要研究了大高径比za27合金铸件挤压铸造过程的若干基本问题。

• squeeze casting can not only improve the gravity segregation and distribution of the chemical constitution of the cast but also the microsegregation of bar-shaped za27 alloy.

  挤压铸造使棒状za27合金铸件的比重偏析有所改善，铸件成分分布更加均匀。 挤压铸造可以明显改善棒状za27合金铸件的显微偏析。

• heat treatment blister is one of common defects of squeeze casting parts, which has some relations with molding method, process and mould.

  热处理起泡是挤压铸件常见的缺陷之一，它与挤压方式、工艺、模具等有关。

• in the paper, the hot crack for the forging die made by methods of squeeze casting is analyzed, how to reduce the hot crack is also given out.

  从生产实际出发，分析了锻模液态模锻成形过程中热裂纹形成的主要原因，提出了降低锻模热裂纹的几点措。