英语释义

• a gauge for measuring strain in a surface

片语

strain n gage应变计

strain-gage amplifier应变式放大器

strain-gage pickup应变计传感器

strain-gage based应变规基座英语

strain-gage element应变片元件

strain-gage indicator应变仪指示器

strain-gage transducer应变计换能器

strain-gage instrumentation应变测试器

英汉例句

• the strain gage based on mechanical principles is the scratch gage.

  以机械原理为基础的应变计是刻痕应变计。

• the rank of accuracy of electric resistance strain gage factor is evaluated according to the sampling theory of large samples or small samples.

  本文采用大子样、小子样抽样理论的数理统计方法，评定电阻应变计灵敏系数的精度等级。

• by means of this technique, the elastic modulus of sea ice has been measured under uniaxial compression. the results are rather close to those obtained by strain gage method.

  应用此技术测量了单轴压缩下海冰的弹性模量，实测结果与电测法的结果符合程度良好。

• to generate the required bending strain, a slit is cut on one side to create bending bridge on the opposite side, to which a strain gage is bonded.

  以产生所需的弯曲应变，狭缝是削减对一方创造弯曲大桥的对岸，一个应变片是保税区。

• the calibration test is key to measure landing gear loads by strain gage method.

  用应变法测量起落架的使用载荷，地面校準试验是载荷测量成功的关键。

• a dynamic strain gage is developed for dynamic stress test at 900℃ of turbine rotor blades of an aeroengine.

  为了对某型航空发动机涡轮转子叶片在900℃高温下进行动应力测试，研制了900℃动态应变计。

• this article treats development of strain signal transfer. measurement and data storage technique for strain gage measuring stress of structure.

  本文主要介绍应用电阻应变计测量结构或部件变形时，应变信号的传递、测量和贮存技术的发展情况。

• experiments of using strain gage to measure the quasi-static stress-strain curve of materials directly were introduced.

  本文介绍了用应变片直接测量材料的準静态应力-应变曲线的试验研究。

• an alternate method of calibration that is simple and accurate would be to employ a hydraulic load cell to precisely meter the force applied to the strain gage load cell.

  另外一种方式进行校準是简单，準确，将聘请一名水力负荷细胞 ，正是米的力量应用到应变片式称重传感器。

• the behaviour of some kinds of resistance strain gage under vacuum is investigated.

  本文探讨了电阻片在真空条件下的行为。

• the experimental set-up and the vibration control system are designed for a class of macroscopically intelligent mechanisms featuring piezoceramic actuators and strain gage sensors.

  设计了具有压电陶瓷作动器与电阻应变计传感器的宏观智能化机构实验装置及其振动控制系统；

• typical sources of variation in assembly line strain measurement include: strain gage type, attachment process, placement accuracy to location target and data acquisition system.

  组装过程中应变测量的典型变异来自：应变片类型，粘贴工艺，定位準确度学和数据采集系统。

• practical calculating method for main tower lengthwise buckling and the method of using steel chord strain gage actual measuring the key section of main tower are presented.

  同时针对悬索桥施工期主塔受力的不利情况，提出了施工期考虑主缆作用的主塔稳定实用分析方法和采用钢弦应变计进行主塔应力实测的有效方法；

• an active vibration control methodology was investigated for flexible redundant manipulators featuring piezoceramic actuators and strain gage sensors.

  研究了具有压电作动器与应变传感器的冗余度柔性机器人的振动主动控制问题；

• a method 「extracting the resonance peak of freqency spectzrum」 is applied in dynamic mathematical modelling a strain gage pressure transducer with inlet pipe and pressure chamber.

  采用「共振峰提取」的方法对带管腔结构的平膜片应变式压力传感器建立了动态数学模型。

• a method for measuring the thickness of the elastohydrodynamic lubricating oil film using a strain gage is presented.

  本文介绍用电阻应变法测量弹性流体动压润滑油膜的厚度。

• this paper introduces application technique of the mid-temperature strain gage in mid-temperature transducer.

  本文介绍了中温应变计在中温传感器上的应用技术。

• a study of milled glass fiber reinforced composites used as the strain gage backing material is present in this paper, which made it suitable more well for the demands of load cell.

  为了满足传感器的使用要求，本文以玻璃纤维增强环氧树脂基复合材料薄膜作为传感器应变片的基底材料。

• lastly, method of pretension controlling by strain gage had higher reliability than using axial-force meter in determining anti-sliding coefficient.

  利用在螺桿上粘贴应变片来控制预拉力方式测定抗滑移系数的可靠性高于轴力计控制预拉力方式。

• it can solve the difficulty of low insulation resistance of high temperature strain gage adhesives and can raise the accuracy of high temperature strain measurements.

  这种方法可以解决无机应变胶高温绝缘电阻过低的问题，并可以提高高温应变测量的精度。

• strain gage hole drilling method is one of the most popular residual stress measurement methods.

  应变片鉆孔法是工程中应用最广的残余应力测量方法之一。

• the hydraulic load cell can also be very useful for calibrating other force measuring apparatus, such as those employing strain gage based load cells.

  液压负荷单元也可以是非常有用的标定其他部队的测量仪器，如那些雇用应变片基于负载细胞。

• two basic forms of the resistance strain gage are the bounded and the unbounded types.

  电阻应变片有粘贴式和非粘贴式两种基本形式。