英语释义

1. any of various high-strength often complex alloys resistant to high temperature

片语

superalloy inin718合金

die superalloy模具高温合金

Ni3Al superalloyNi3Al高温合金

dz superalloydz125合金的

superalloy blisk高温合金涡轮

K445 superalloyK445高温合金

superalloy coating基高温合金涂层

base superalloy基高温合金

GH708 superalloyGH708高温合金

英汉例句

• The wide range of investigations shown shut lower yield strength, coarse grain size and metallurgical flaws were the basic causes for the earlier failure of superalloy for turbine disk.

  广泛的研究表明，屈服强度低、粗晶粒尺寸、冶金缺陷的存在是造成涡轮盘用高温合金早期失效的主要原因。

• The undercooled DZ125 superalloy was investigated by the method of glass and molten salt purification combined with cycled superheating, the mechanism of purification by compound salt was discussed.

  采用自制凈化剂和循环过热相结合的办法，研究了不同凈化剂对DZ125高温合金的凈化效果，探讨了复合熔盐的凈化机理。

• GH543 cobalt-free nickel base superalloy is finally selected from the final 12 compositions extracted through theoretical analysis.

  无钴镍基高温合金GH 543即是从理论分析的最终的12种成分中选择出来的。

• Low cycle fatigue (LCF) tests of a directionally solidified nickel base superalloy were conducted at elevated temperatures.

  本文研究了一种定向凝固镍基高温合金的高温低周疲劳行为。

• The effect of electron beam surface solidification treatment on microstructure of superalloy M38G and oxidation resisfance of solidified layer has been studied.

  采用电子束表面熔凝处理方法研究了电子束表面熔凝处理M38G高温合金熔凝层组织和熔凝层组织对高温氧化的影响。

• The effect of aging treatment on the tensile strength, elongation, hardness and microstructure of a cobalt base superalloy used for pistons rings was investigated in this paper.

  本文研究了不同热处理时效温度和时效时间对一种活塞环用钴基高温合金的抗拉强度、延伸率、硬度及组织的影响。

• The formation of the microstructure and the evolution process from dendrite into equiaxed structure during atomized process for spray formed superalloy were analyzed.

  对喷射成形高温合金的组织形成及其从雾化过程的树枝晶向等轴晶组织的演变过程进行了分析。

• The revert amount of K424 superalloy is quite great because of the wide application.

  镍基铸造高温合金K 424使用量多，返回料数量大。

• The second moment creep time of DZ4 superalloy rapidly decreases with the increasing of temperature and stress.

  随着温度的升高和应力的增加，DZ 4合金蠕变第二阶段的时间迅速减少。

• The ingots of cast superalloy K4169 was refined with the addition of a trace of intermetallic compounds to the melt under conventional casting condition.

  采用一种新型中间合金复合细化剂，在常规生产工艺条件下对高温合金K4169铸件进行了晶粒细化。

• By means of stereomicroscopy and scanning electronic microscopy (SEM), the fracture mode and mechanism of the broken K18 superalloy cast blade in a supercharger turbo were investigated.

  采用体视显微镜、扫描电镜等分析手段对K18合金增压器涡轮铸造叶片的断裂形貌与断裂机制等进行了分析。

• Possibility to dope Y2O3 particle on the surface of superalloy sample and the relationship between homogeneity and irradiation parameters of laser have been investigated by means of laser irradiation.

  本文通过激光辐照的方法，研究了在高温合金试样表面掺杂Y_2O_3质点的可能性、均匀程度与激光辐照参数的关系。

• The effect of melt overheating treatment on the solidification segregation of M963 cast Ni-base superalloy has been studied.

  研究了熔体过热处理对M963铸造镍基高温合金凝固偏析的影响。

• After electron beam welding, electron beam local heat treatment was applied in GH4133 superalloy as the turbine disk material in this paper.

  针对涡轮盘材料GH4133合金，在电子束焊后采用新颖的电子束局部热处理工艺对接头进行热处理。

• An experimental study on the fatigue crack growth of GH4169 superalloy has been carried out.

  本研究中对GH4169高温合金的疲劳裂纹扩展性能进行了试验研究。

• High temperature stress rupture behaviour of single crystal Ni-base superalloy prepared by different withdrawal rate has been studied.

  研究了不同拉晶速率下制得的镍基单晶高温合金的高温持久变形行为。