英汉例句

• The clamping force which is determined by grinding force is used for calculating stiffness and operating torque when tighting sand skin.

  由磨削力确定夹紧环所需的夹紧力，以此计算夹紧环的刚度和尺寸，并校核其强度和张紧砂布时的扳手力矩。

• This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method.

  针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟，得到径向位移、接触应力、锥面间隙结果。

• When jigs and fixtures are designed, the clamping system is designed to ensure that the correct clamping force is applied, and that the clamps can be operated quickly but with safety.

  在设计鉆模和夹具时，要同时设计装夹系统来保证提供恰当的装夹力，并使装夹操作快速而安全。

• The clamping force control and the ratio control is the most important parts of the CVT control technology.

  夹紧力控制与速比控制是CVT控制问题中最为重要的两个方面。

• Fixture layout and clamping force are two main aspects that influence the degree and distribution of machining deformation.

  夹具布局和夹紧力是两个影响的程度和加工变形分布的主要方面。

• It is guarantee to get high quality casting that inner casting path and air outlet path are reasonably designed, the rotary speed and clamping force of silicon rubber plats are correctly celebrated.

  合理设计铸模的内浇道、出气道，正确选择离心浇注旋转速度和硅橡胶盘片的夹紧力，是获得高质量铸件的保证。

• The locking sound device for the drill chuck has the advantages of capability of making the clamping force of the drill chuck controllable and prompting users.

  该发明具有可使鉆夹头夹紧力可控并提示使用者的优点。

• To prevent sliding of the workpiece, the clamping force least required is calculated by dividing the maximum cutting force in the X-Y plane by the frictional coefficient and number of clamping points.

  为了防止工作的滑行，用摩擦因数和夹持点数去除X-Y平面的最大切削力计算出夹持力最少应为多少。

• In using an injection moulding machine, it is best to use the minimal but adequate clamping force f.

  使用注射成型机，最好使用最小同时充足的锁模力f。

• A convenient method to calculate the minimum clamping force for milling process was presented.

  提出了一种计算铣削加工中夹紧工件所需最小夹紧力的简洁方法。

• In this paper, the locating, clamping force and location errors are analyzed. In the end, we give improved scheme for the jig.

  本文就磨工艺圆尖的夹紧定位、受力和定位误差进行了分析，并对存在的问题提出了改进方案。

• The elastic rigidity of rail pad and ballast stiffness of rail and clamping force of fastener are the main factors that cause the widening of gauge.

  钢轨垫层和道床的刚度、轨刚度和扣件扣压力是影响轮轨之间作用力和轨距扩大的主要因素。

• The more the blasting clamping force is, the more blasting vibration is produced to the adjacent tunnel.

  爆破夹制作用越大，邻近隧道产生的爆破振动越大；

• Fixture optimization is a new fixture design method that develops with the extensive application of optimization techniques. It includes fixture layout optimization and clamping force optimization.

  夹具优化设计是一种随着优化的广泛应用而发展起来夹具设计新方法，包括布局优化和夹紧力优化。

• The new swing clamps maintain the total clamping force by a patented self-locking device if hydraulic pressure is cut off or drops.

  新的摇摆夹维持专利自锁装置的总锁模力液压如果被切断或下降。

• The clamping force determines the transferable torque.

  夹紧力决定了可传递的转矩。

• Controls of ratio and clamping force of pulley are designed.

  对电控系统中速比与带轮夹紧力的控制进行了具体设计。

• Movement, clamping were completed by two cylinder, the movement is smooth, the clamping force is easy to control, ensure the ironing quality.

  运动、夹紧分别由两个气缸完成，运动平稳，夹紧力易于控制，保证熨烫质量。

• Based on the theory of slip line and plastic deformation of metal, the clamping force for forging reduction of cylinder is analyzed and studied.

  应用滑移线理论和金属的塑性变形理论，分析研究圆柱体镦粗过程中的夹紧力的计算方法，并与试验结果进行比较。

• And the same time because of the two-step force-amplifier, lower press result in the smaller clamping force of pneumatic drive system is solved.

  同时由于采用二级增力机构，解决了一般气压传动夹具因压力较低而导致夹紧力不足的缺点。