片语

additive efficient deformation rate有效附加变形率

plastic deformation rate塑性形变率

strength and deformation discount rate强度和变形折减率

deformation accumulative rate形变累积率

casing deformation rate套管变形率

deformation recovery rate变形恢复率

modern terrain deformation rate现代地形变速率

英汉例句

• for as-sintered alloys from mixed powders, the compressive strength increased and the ductility decreased when enhancing deformation rate or lowering deformation temperature.

  结果表明，对于混粉烧结合金，增大变形速率或降低变形温度，合金的强度增大，延性降低；

• the influences of deformation rate on the mechanical properties of 304 austenitic stainless steel were studied by tensile test at room temperature.

  采用室温拉伸实验研究了不同变形速度对304奥氏体不锈钢力学性能的影响规律。

• differential scanning calorimetry (dsc) was employed to investigate the relation of deformation rate and eutectic melting activity energy of az91d magnesium alloy by sima method.

  采用dsc技术研究了sima法制备半固态az91d镁合金坯料过程中形变率与共晶熔化激活能的关系。

• according to the vertical deformation rate mapping for chinese mainland during 1951-1990, the relationship between high-gradient belts and strong earthquakes are obtained.

  并且依据1951~1990年中国大陆垂直形变速率图计算分析了垂直形变速率梯度，研究了高梯度带与大震的分布关系。

• however, this paper discovers that the driving performance of the actuator is not only related to the deformation, but also to the deformation rate under further study.

  然而经深入研究发现：压电陶瓷驱动位移大小，不仅与其变形量有关，而且与其相应变形量的时间长短有关，即变形速率有关。

• the shanxi graben zone has the largest fault deformation rate showing it is the most important block boundary of north china.

  山西断陷带的断层形变速率最高，是华北地区最重要的活动块体边界；

• finally, the relation among component of shear deformation, component of extension deformation and deformation rate and tectonic earthquake is analyzed on the basis of a example.

  最后根据实例计算结果分析了剪切变形分量、扩张变形分量与形变速率、构造地震的关系。

• the temperature and the deformation rate are the key factors to prepare ultra-fine grain materials.

  变形温度和变形速率是获得超细晶材料的关键。

• in order to increase the volume deformation rate as lpg bottle broken, a boss-backing has been developed for welding the bottles.

  为提高液化石油气钢瓶破裂时的容积变形率，研制了带有凸台结构的焊接衬圈。

• the magnitude and symbol of the residual stress greatly depends on the initial deformation rate of the pipe under drawing with the working tools.

  残余应力的符号和大小在很大程度上取决于钢管在拔制工具中的初始变形率。

• the influences of deformation temperature, deformation rate and deformation degree on the flow stress and grain size are different. the deformation degree mainly influences the shape of flow curves.

  结果表明：变形温度、变形速率和变形程度对流动应力和再结晶晶粒尺寸均有不同程度的影响。

• so, using the digital deformation data to calculate the crustal deformation rate can be taken as a seismic method in the routine seismic prediction.

  因此，应用形变数字化资料计算地壳形变速率，可作为对地震活动以及日常地震预测的一种分析方法。

• the test results indicate that the swelling deformation rate in the early stage may affected by the inundation ways, but the ultimate deformation rates should be the same.

  试验结果表明，不同浸水路径在浸水的初期阶段对膨胀土的膨胀变形速率有一定的影响，但膨胀率最终值基本一致；

• the effect of carbon, molybdenum and rare earths on hot cracking susceptibility of austenitic stainless steel welds was studied with continuously variable deformation rate cracking test (vdr) method.

  应用变形速率连续可变式热裂纹试验方法（vdr法）研究了碳、钼和稀土元素对奥氏体不锈钢焊缝热裂敏感性的影响。

• the isoplethes of vertical deformation rate or their tangents are almost perpendicular to fault line.

  形变速率等值线在其偏转处的切线几乎与断裂线正交。

• with the humidity further diffusion, the deformation of tunnel increases but the deformation rate decreases, and eventually converges.

  随着湿度的进一步扩散，隧洞的变形总量增加，但变形速率逐渐降低，并最终得以收敛；

• some main processing parameters are briefly introduced, such as speed of main shaft, feed rate, shape of spinning wheel, deformation rate of each step and structure of template.

  对主要工艺参数如主轴转速、进给率、旋轮形状、道次变形率、模板形式等作了简要介绍。

• the results show that the ductile deformation rate is proportional with the fault-slip rate. in the rifting phase, the fault slipping is severe while the ductile deformation is very fast.

  渤海湾歧口凹陷的伸展计算结果显示韧性变形速率与断层滑移速率呈正比关系，盆地在裂陷期不仅断层滑移剧烈，韧性变形速率也很大。

• deformation rate influence the temperature rise of forging, a reasonable choice could influence the forging of forming to a certain extent.

  变形速率影响锻件的温升，其合理选择对锻件成形有一定影响。

• rolled molybdenum plate has a high density, even close to its theoretic value when the deformation rate is higher than 50%.

  经过轧制的钨板具有很高的密度，变形率达到50%以上的钨板的密度基本上接近理论密度。

• present crustal stress values are high, structural deformation rate is fast, intensity of earthquake has an obvious increasing trend, and terrestrial heat flow anomaly is very obvious.

  现代地壳应力值高，构造变形速度快，地震活动强度加剧，地热流异常明显。

• while for the alloys from milled powders, the compressive strength increased and the ductility decreased when enhancing deformation rate or lowering deformation temperature.

  对于球磨粉末烧结合金，增大变形速率或降低变形温度，合金的强度增大，延性降低。