片语

deformation with temperature温度变形

Heat deformation temperature热变形温度

deformation start temperature热变形温度

thermal deformation temperature热变形温度

deformation by temperature温度变形

hull deformation by temperature difference船体温差变形

deformation at high temperature高温变形

deformation deformation recovery temperature形变回复温度

ash deformation temperature灰变形温度

英汉例句

• The microstructural changes produced by increasing the hydrogen content at a fixed deformation temperature correspond to those ob…

  相同温度变形的试样中氢含量增加所产生的组织变化与在更高温度压缩后所产生的组织变化相当。

• The evolution law of microstructure and properties of 7a04 alloy at different deformation temperature and times was studied.

  研究了不同变形温度和变形次数下7a04铝合金组织与性能的变化规律。

• Thermal deformation temperature and liner expansion coefficient of the composite were decreased.

  该复合材料的热变形温度有所降低，但线膨胀系数减小。

• When deformation temperature is constant, flow stress increases with the increase of strain rate.

  当温度一定时，流变应力随着应变速率的升高而增大。

• The deformation temperature is the main factor which affects the grain size of austenite or ferrite when the strain rate is not changed largely.

  说明在变形速率不太高的情况下，变形温度是影响奥氏体或铁素体晶粒尺寸的主要因素。

• The effect of deformation temperature on microstructure and property of MP159superalloy has been analysed and a reasonable range of deformation temperatures for MP159 alloy has been obtained.

  分析了变形温度对MP159 高温合金组织、性能的影响规律，得出了该合金合理的变形温度范围。

• The inner maximum resistance force and the maximum stress of the specimen decreases as the deformation temperature increasing.

  在形变速率相同的条件下，随变形温度的升高，试样内部最大形变抗力及最大应力呈下降趋势。

• The dynamically recrystallized grain size increases with increasing deformation temperature and reduces with increasing strain rate.

  动态再结晶晶粒尺寸随着变形温度的升高而增大，随着应变速率的升高而减小。

• Based on the resin curing the hardness and thermal deformation temperature higher, but also has a good climate of tolerance and toughness.

  其基础树脂固化后的硬度和热变形温度较高，同时又具有良好韧性和耐气候性。

• With the decreases of deformation temperature and increases of deformation degree and deformation rate, the recrystallized grain size decreases and the recrystallization volume percent increases.

  随着变形温度的降低、变形程度和变形速率的增大，再结晶晶粒尺寸减小，再结晶体积分数增大。

• The results show that the model of deformation resisitance is different at the same deformation temperature and the different stain rate.

  结果表明：在同一温度下，应变速率不同，材料的流变应力模式不同；

• The resin toughness, the casting of the thermal deformation temperature is a good Comprehensive Performance winding resin.

  该树脂韧性好，其浇铸体的热变形温度高是一种综合性能良好的缠绕用树脂。

• Impact rupture suface of the composites was observed by scanning electron microscope, and the load deformation temperature and mechanical properties were tested.

  通过扫描电镜观测了复合材料沖击断面的形貌，测试了复合材料的负荷变形温度和力学性能。

• The microstructure of tensile samples was observed and analysed, and then the effect between stacking fault energy of TWIP steels and deformation temperature was calculated by thermodynamic model.

  观察分析了拉伸试样的显微组织，并利用热力学经典模型，估算了温度对孪晶诱发塑性（TWIP）钢层错能的影响。

• The microstructural changes produced by increasing the hydrogen content at a fixed deformation temperature correspond to those obtained by raising the deformation temperature.

  相同温度变形的试样中氢含量增加所产生的组织变化与在更高温度压缩后所产生的组织变化相当。

• The resin toughness, the casting of the thermal deformation temperature is a good comprehensive performance winding resin.

  该树脂韧性好，是一种综合性能良好的缠绕用树脂。

• Effects of SS400 steel's deformation temperature and strain rates on its deformation behavior was studied using single pass compressing test.

  采用单道次压缩试验，研究了变形温度和变形速率对SS400钢热变形行为的影响。

• The results of experiments show that tensile strength, bend strength, bend modulus and heat deformation temperature of the composite materials are increased with the increase of carbon fibre content.

  随碳纤维比例的增大，该复合材料的拉伸强度、弯曲强度、弯曲模量及热变形温度均呈上升态势；而缺口沖击强度及击穿电压呈下降态势。