英语释义

1. a point, line, or surface whose motion generates a line, surface, or solid

片语

copper generatrix铜母线

bus bars母线（bus bar的复数）

generatrix directions母线方向

Generatrix cease母线停运

basket generatrix转鼓母线

median generatrix中母线

side generatrix侧母线

busbar母线，汇电板；汇流排；电压衡定可过高电流的电导体

generatrix brazing铜排焊接

curved generatrix曲母线

generatrix-[数] 母线；母面；母点

英汉例句

• by means of fea, it is concluded that the stress relief groove with an elliptical generatrix has the best effect of stress relief.

  通过有限元计算与分析，得到应力释放效果最好的是母线为椭圆线的减应力结构。

• adopting the engaging process of the measuring rack- probe, the error of straight generatrix is measured, and by error analysis, the tooth profile error and tooth orientation error can be obtained.

  采用刃边齿条测头，测量齿轮廓面的直母线偏差，通过误差分析分离出齿廓总偏差和螺旋线总偏差。

• there are mainly four parts in the new type data collection system: generatrix signal collection device;

  本文设计的新型数据采集系统主要包括四个部分：母线信号采集装置；

• because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means.

  由于燃烧室外表面的母线轮廓复杂，手工编制数控加工程序难度大。

• self-integral rogowski current coil is used parallel sampling resistance in the out-port, and is selected the small magnetic conductivity copper or aluminum as the generatrix to be measured.

  自积分式罗果夫斯基电流线圈是在输出端并联一的采样电阻，并选用磁导率小的铜或铝作为与线圈配合的待测母线。

• the conclusion of how to determine error between generatrix linearity and axes linearity and how to compensate the error are valuable in measurement of axes linearity of deep bore.

  给出的母线与轴线直线度误差及误差消除的方法，对深孔直线度的测量具有一定的实用价值。

• a novel method that can rapidly recognize short-circuit for the dc system is proposed according to the integrative criterion of loop current and generatrix voltage measured by the hoer sensor.

  提出利用霍尔传感器测量直流回路、母线电压，以电流、电压综合判据快速识别直流系统故障的方法，并研制了直流系统三段式微机电流保护装置。

• the third section put emphasis on how to solve generatrix of rotation surface and use b-splineto fit generatrix of rotation surface, and also examples are listed.

  第三部分提出了一种旋转曲面旋转轴反求的方法，利用b样条曲线拟和旋转面的母线并给出了算法实例。

• the temperature in generatrix layer is higher than in the worm wheel layer.

  母线层的温度较高，而蜗壳层的温度较低。

• this paper presents a practical method of directly measuring diameter, taper and generatrix straightness of conical workpiece in precision lathe by separating movement errors of mechanical system.

  本文提出了一种在精密车床上直接测量锥形工件的直径、锥度及素线直线度等参数的实用方法。

• the study result of stress distributing with heavier deflected load on roller has important reference to the generatrix shape trimming.

  文中还指出，关于较大偏载状况的滚子接触应力分布规律的研究，对滚子母线进行合理修形具有参考价值。

• all inverters on one dc generatrix decrease power consuming in the fieldbus.

  并且由总线控制的变频器采用了共直流母线技术大大降低了能耗。

• the evaluating model of straight generatrix error data is established.

  建立了直母线误差数据的评定模型；

• according to the restriction of the generatrix line bertrand surface can be constructed with the bertrand curve with broad sense group.

  按照母线的约束，形成广义白川德曲线族，进而构造出白川德曲面。

• please analyse what causes the electromagnetism resonance in the process of generatrix cease, as well as how to guard against when the equipment and the operator is under the operation.

  本文分析了母线停运过程中，电磁谐振产生的原因，以及在设备上及运行人员在操作上如何进行防范?。

• in order to avoid power cut during examining and repairing of generatrix or conk out of this operation mode, breaker can be used to separate mono generatrix.

  为了避免这种运行方式在母线检修、故障时可能造成停电的缺点，因此可用断路器将单母线分段。

• the former is similar to bulge, but the deforming mode of the latter is rolling in which the stress is tensile in generatrix direction and the wall thickness are mainly reduced in this zone.

  前者的受力情况类似于胀形，后者为母线方向拉应力作用下的辗压变形，该区起主要减薄壁厚的作用。

• the main wiring uses the single generatrix emanant wiring plan.

  主接线采用单母线放射式接线方案。

• an efficient method for measuring taper angle deviation and generatrix straightness of machined parts with large sizes without unloading the machined parts from the machine tool is proposed.

  本文提出了一种能在机床上直接测量大尺寸外圆锥锥角偏差和素线直线度误差的新方法。

• a new algorithm of solving the intersecting line equation for multi-pipe is presented by means of coordinate transformation and generatrix comparison.

  利用坐标变换、母线比较等方法，形成了求解空间多管相贯相贯线展开方程的新算法。