片语

guide chase vane wheel导向叶轮

guide chase vane ring导向叶环

hollow guide-vane空心导叶

guide-vane servomotor导叶式伺服电动机

guide-vane packing导叶密封条

guide-vane ring导向叶环，导叶环

guide e vane导向叶片

guide chase vane apparatus导向叶片装置

英汉例句

• for validating the aerodynamic characteristics of lp turbine guide vane, the wind blow was carried out for test cascade of the guide vane on the low speed annular wind tunnel.

  为了考查低压涡轮导向器的气动性能，在低速环形叶栅风洞上对导向器的实验叶栅进行了吹风实验。

• with the help of model tests, it is found that the presented design method of the guide vane can provide a higher hydraulic efficiency and better erosion-proof than conventional method.

  经模型试验表明，与传统方法设计的导叶相比，用本文提出的方法设计的导叶在含沙水流中运行时，水力效率高，耐磨蚀。

• guide vanes have inhibiting device, and the guide vane which has been cut off will not spin in order to avoid collisions with other guide vanes.

  导叶设有限位装置，剪断销剪断的导叶不能随意转动，避免与其他导叶碰撞。

• li caihui solving method for development of back guide vane of the fan is introduced.

  介绍了通风机后导叶展开的计算方法。

• the origin of the unit vibration in small guide vane opening is analyzed when the unit is closing and the optimal scheme of the unit closing law is suggested.

  本文拟对关机过程中导叶小开度振动原因进行分析，并对机组关闭规律的优化方案及实施过程进行介绍。

• the guide vane safety device include three kinds of structures, the destructive structure concerning shear pin and snap pin;

  导叶安全保护装置主要包括：破坏性结构，剪断销、拉断销；

• optimum guide vane and bucket positioning with flow field characterris-ics both for clean and sandy water are…

  得到了在清水和含沙水条件下两种活动导叶与固定导叶的最佳相对安放位置和流场的不同特性。

• a reform scheme with exit guide vane remained for large axial flow pumps is discussed deeply.

  对大泵改造保留出口导叶的叶轮改型方案作了深入的探讨。

• in this paper, the optimum position between the guide vane and the stay gate is given and the optimum design parameters are put forward.

  在分析了三种不同位置时的水力损失后，给出了固定导叶与活动导叶的最佳位置关系，提出了双列叶栅设计时的最优设计参数。

• the principle and characteristic of three angle measurement methods are introduced; digital measurement approach is selected to design adjustable guide vane angle detection system.

  介绍并比较了三种自整角传感器角度测量方法的原理、特点，并选用数字测量计算法实现进气可调导流叶片转角检测系统。

• on the basic of former engine, the angle variable partial program of the fan and compressor guide vane of engine mathematical model is been renewed.

  在原发动机模型的基础上，补充编制了发动机数学模型的风扇和压气机导叶角度可调的部分程序；

• to ensure the install convenience of guide vane and operating structure, first guide vane should be turned off, and then connect guide vane operation structure.

  为保证导叶和操作机构安装方便，先将导叶置于全关位置，再连接导叶操作机构。

• guide vane two section close valves normally installed in vane control circuit to prevent axial flow turbine from raising during shut-down period.

  为防止轴流式水轮机在停机过程中产生抬机现象，多在导叶操作回路上安装导叶两段关闭阀。

• the guide vane of the turbine is firstly controlled by hydraulic pressure connecting rod.

  水轮机导叶控制装置首次采用液压连桿；

• guide vane operation structure includes the guide vane arm clip board, guide vane arm, segmental keys, connection board, handle, cut pin, connecting rod pin and gland, etc.

  导叶操作机构主要包括：导叶臂压板、导叶臂、分瓣键、连接板、耳柄、剪断销、连桿销及压盖等。

• in order to investigate the flow characteristics of cooling flow downstream of a turbine guide vane trailing edge slot , numerical methods of rng k-ε turbulent model were solved.

  通过rngk-ε湍流模型求解可压流的n-s方程，研究燃气轮机涡轮导向叶片尾缘劈缝出流冷气的流动情况。

• based on the consideration of nozzle ring pneumatic torque transmission, the torque of pneumatic force acting upon nozzle guide vane was acquired by calculation.

  在考虑了喷嘴环气动转矩的传递过程后，通过换算，求出了气动力作用在喷嘴导流叶片转轴上的转矩。

• presents the failure of the inlet guide vane of the atomization air compressor, analyzes the reasons and puts forward the solutions.

  介绍雾化空气压缩机进口导叶的损坏情况，进行原因分析，提出解决问题的对策。

• optimum guide vane and bucket positioning with flow field characterris-ics both for clean and sandy wat…

  得到了在清水和含沙水条件下两种活动导叶与固定导叶的最佳相对安放位置和流场的不同特性。