英汉例句

• Furthermore, the scanning speed has an important influence on the size of phase change region and thermally affected region.

  激光扫描速度对相变硬化区和热影响区的大小有极大的影响。

• The scanning speed of nozzle has a great effect on the pore structure of copper deposits.

  喷嘴移动扫描速度对铜电铸层多孔结构有明显的影响。

• Application of multi-threading technology to improve scanning speed is the main feature of this program.

  应用多线程技术提高扫描速率是本程序的主要特点。

• Of course sheet scanning speed may vary depending on the scanning equipment, if with high-speed scanning speed, that just like the speed of paper money, everyone knows that how fast.

  当然答题卡扫描速度的快慢取决于所用的扫描设备了，如果用高速扫描仪扫描的速度，那就像点钞机过钞票的速度一样，大家都知道那有多快。

• The influence of coating, spot size, power and scanning speed on hardening layer features and wear resistance were studied.

  研完了表面状态、斑尺寸、率及扫描速度对硬化层特征及耐磨性的影响。

• In clinical applications, it is important to select appropriate scanning speed to obtain both high ablation rates and minimal thermal injury.

  因此，在临床应用上，应根据临床需要选择合适的扫描速度和辐射曝光量来获得大的消融率和小的热损伤。

• The relationship between the section area of the molten layer and the scanning speed of the laser beam is close to hyperbolic under certain conditions.

  熔化层的横截面积与激光束扫描速度之间在一定条件下接近双曲线关系。

• With the scanning speed going up, the hardness and the wear - resisting property are improved.

  随着激光扫描速度的增加，硬化区硬度和耐磨性增大。

• Preset layer thickness and laser scanning speed have definitive matching relation to the content of amorphous in the coatings, respectively;

  预置涂层厚度及扫描速度分别与涂层中非晶含量存在着一定的匹配关系；

• The effect of both laser power density and scanning speed on coating microstructure was remarkable.

  激光功率密度和扫描速度对涂覆层微观组织结构有显着影响。

• Its antenna beam scanning entirely electronically controlled beam scanning speed is not only high, but the number of beams, movement pattern can be arbitrarily controlled.

  其天线波束的扫描完全用电子的方式控制，不但波束的扫描速度极高，而且波束的数目、运动方式都可以随意的控制。

• Under the conditions of other technological parameters unchanged, the microstructure of the coatings becomes smaller and more homogeneous with laser scanning speed increasing.

  在其他工艺参数不变的条件下，随扫描速度的增大，熔覆层组织变得细小、均匀；

• The martensitic and undissolved carbide contents continuously increase as the laser scanning speed increases while the residual austenite decreases.

  随激光扫描速度增大，试样中的马氏体和未溶碳化物的含量不断增加，残余奥氏体含量则连续下降。

• If the scanning speed is not changed, the optimization of scanning paths will directly influence the machine time of each layer.

  扫描速度一定时，扫描路径的优化与否将直接影响加工时间。

• The laser scanning paths and scanning speed usually influence the machine time of each section.

  激光扫描路径和扫描速度影响每层加工时间。

• When the laser scanning speed increases, the laser radiation and cooling time get shorter, so the growing direction of microstructures is changed sharply.

  提高激光扫描速率，造成激光辐射和冷却时间变短，合金微观组织生长方向变化显着；

• The results show that the laser power and scanning speed affect the performance of coating shaping significantly, while overlapping has less influence on shaping.

  结果表明，激光输出功率、扫描速度对熔敷层成形的影响显着，而搭接率的影响程度较小。

• While, Uses multi CCD, the scanner to be possible to enhance the scanning width, the scanning speed and the scanning precision, in the similar product this is a prominent superiority.

  同时使用多个CCD的扫描仪可以提高扫描的幅面、速度及精度，在同类产品中这是个突出的优势。