英语释义

1. a knuckle made to furnish a bearing for an automobile steering wheel, pivoted to the axle, and controlled in its swiveling motion by the steering gear

片语

steering g knuckle arm转向节臂

steering knuckle tie rod转向节系桿

steering cylinder linkage knuckle转向油缸桿件铰接头

steering axle knuckle转向轴关节

steering knuckle bushing转向节衬套

steering knuckle bearing preload转向节轴承预加负荷

steering knuckle turning angle转向节转角

Steering knuckle arm bearing汽车转向臂轴承

steering knuckle arms[车辆] 转向节臂

英汉例句

• assuming that the knuckle face plates have been fabricated (and welded to the frame), the steering knuckle assembly can now be assembled.

  假设猪脚面板已制造（和焊接到框架）中，转向节大会，现在可以进行组装。

• it was presented that a new precision forming technology of car steering knuckle in this paper.

  文章提出了轿车转向节精密成形新工艺。

• macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope.

  采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。

• the hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly.

  车辆转向时，支柱以及转向关节（经由球形接头与上支柱固定器之轮毂轴承）会一体旋转。

• a worn steering knuckle arm on a motor vehicle may cause heavier steering operation, the reasons are studied in this paper according to the steering trapezium principle.

  根据转向梯形机构的工作原理，分析了已磨损的转向节臂导致转向沉重的原因。

• the last modification required to the brake faceplate, is making the plate flush with the steering knuckle faceplate.

  最后修改面板所需的制动，转向是使板与关节沖洗面板中删除。

• the trike frame should now be nearing completion and only requires the installation of the steering knuckle mounting plates to be complete.

  该三轮车框架现在应该已接近完成，只需要安装指导安装板的关节完整。

• steering axis inclination is the inward tilt of the steering knuckle at the top.

  督导轴倾角是外来倾斜的转向节在最上方。

• lots of well-forged, normatively heat-treated, and elaborately-processed steering knuckle arms, pitman arm, idler arm pendulum lever etc, can be used widely as parts of various types of truck and car.

  众多锻造精良、热处理规范、加工精细的转向节臂、摇臂、随动臂、摆臂等品种，可为载重车、乘用车广泛地提供所需型号的配套件。

• by improving the design of forging die and using press-forging and backward extrusion principle, solves the problems of 130 steering knuckle forming which can not be fully filled during forming.

  通过改进预锻模膛的设计，利用镦粗成型、反挤成型的原理，有效解决了130转向节板部模锻成型时充不满的问题。

• the authors carried out a fracture failure analysis for a steering knuckle arm, and concluded that the part failure was caused by fatigue.

  对转向节臂断裂失效进行了分析，确认该零件因疲劳而断裂。

• the production of domestic, import models of the steering section of the main pin, steering knuckle kingpin repair kit is more popular with users alike.

  所生产的国产、进口车型的转向节主销、转向节主销修理包更受广大用户的一致好评。

• a feasible process scheme was made for forming the steering knuckle of a truck based on a technological analysis on the forging of the part.

  通过对卡车转向节锻件的工艺分析，制定了合理的工艺方案。

• the practical production indicates that 7075 aluminum steering knuckle can get excellent forming quality and meet the appliance requirement.

  实际生产表明，采用优化后的工艺成形的铝合金转向节质量良好，符合产品的使用要求。

• six-component forces of all steering knuckle joints were obtained in time history by multi-body suspension system dynamic simulation. then the most easily fatigue damage region was confirmed.

  结合转向节有限元模型，获得了转向节实时等效单元应力，通过统计确定了最易疲劳的损伤区域。

• the effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper.

  研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。

• 「wuhu zhongsheng steering knuckle co. , ltd. 」 is located in wei 2 road, machinery & industrial zone of wuhu county, anhui province, china.

  「芜湖中升汽车转向节制造有限公司」位于安徽省芜湖县机械工业园纬二路。

• remove the steering knuckle from the strut.

  自支柱拆除转向关节。

• place the entire steering knuckle assembly in a vise and re-drill using the #q drill bit.

  广场老虎钳，重新演练整个转向节装配在一个使用＃q鉆头。

• the steering knuckle then supported through ball joints, by upper and lower control arms which are attached to the car frame.

  转向节通过球头节与安装在车架上的上下控制臂相连。

• this movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel).

  这一运动是由装在驾驶员前面的转向盘与转向节（车轮）之间的转向器和连桿装置来共同完成的。

• these include the fabrication of the derailleur cable stop, and drilling the holes for both steering knuckle levels.

  这些措施包括停止生产的变速器电缆，鉆两个孔，关节指导的水平。