片语

welding-seam cleaner焊缝清理机

welding seam traking焊缝视觉跟蹤

welding-seam checking焊缝检测

welded joint焊缝；焊接节点

welding seam tracking焊缝跟蹤

welding seam image焊缝图像

butt welding seam对接焊缝

longitudinal welding seam纵向焊缝

welding seam size焊缝胶

main welding seam主焊缝

welding line焊缝；缝合线

英汉例句

• The droplet transfer in the twin-wire co-pool gas-shielded metal arc welding(TCGMAW) process greatly affects the welding seam appearance and the welding quality.

  双丝共熔池气体保护焊（TCGMAW）的熔滴过渡对焊缝成形以及焊接质量具有重要的影响。

• Also, improve the overlapped length of the tail frame and the frame and change the welding seam into intermittent seam, therefore the frame strength can be effectively increased.

  改善尾架与车架的搭接长度，将连接焊缝改为断续焊缝，从而有效地提高了车架的强度。

• Segmental back welding is adopted for each welding seam to minimize the residual stress and deformation of welding.

  每条焊缝采用分段退焊法，减小焊接残余应力和变形。

• The visual servo and control system for welding seam tracking were validated by experiment, the feasibility also been proved.

  通过实验对焊缝跟蹤视觉伺服控制系统进行了验证，说明了该系统的可行性。

• Results show that cold pressure welding is suitable for zinc alloy. The microstructure of welding seam is compact.

  结果表明，采用合适的冷压焊工艺可以实现锌铝合金的对接，焊缝组织致密。

• The border of laser beam penetration welding seam is simulated by the constructed heat source model and compared with the experimental results.

  应用所建立的热源模型模拟分析了激光深熔焊焊缝边界形状，并与实验结果进行了比较。

• However, because welding seam images are complicated, it is very important to choose suitable and effective processing algorithm in order to get accurately the information.

  在基于视觉的自动焊接中，由于焊缝图像是复杂多变的，要準确得到焊缝位置选择合理高效的处理算法是非常重要的。

• Shield sets the dimensional accuracy and the shape of higher tolerance, the welding seam is also very strict quality requirements.

  屏蔽套的尺寸精度及形状公差要求较高，焊缝的焊接质量要求也很严格。

• Taking the processing the welding seam qualification rate can be increased and also ensured the welding quality in gas piping construction.

  采用此工艺可提高焊缝检验合格率，保证燃气管道施工的焊接质量。

• The paper introduces the structure as a whole of expert system for X_ray welding seam distinguishing.

  介绍了焊缝缺陷识别专家系统的总体构成。

• In this paper, we carried out a series of studies on the V-groove welding seam of the flux core arc welding (FCAW) with rotating arc sensor.

  利用旋转电弧传感器，开展了水下湿法药芯焊丝电弧焊(FCAW)的V型坡口焊缝跟蹤研究。

• The impacts of transverse and longitudinal shrinkage of welding seam on underframe positioning.

  以及焊缝横向、纵向收缩对底架定位的影响。

• Inspection welding seam and dimension of cargo hatch cover.

  货舱舱口盖焊缝和尺度检查。

• The welding thermal cycle and section dimensions of the welding seam were measured in the condition of the simulated welding process parameters for checking simulation results.

  采用模拟时的焊接工艺参数进行钨极氩弧焊平板对接焊，测定焊接热循环曲线和焊缝截面尺寸，对模拟结果加以验证。

• Ultrasonic defect detection inspection shall be carried out for welding seams and defects shall be removed. the excess weld metal of welding seam must be eradicated and abraded after welding.

  焊缝须进行超声波探伤检查并清除缺陷，焊后对焊缝余高进行铲除并磨平。

• A tactile sensor welding seam tracing in welding was designed.

  设计了一种接触式自动焊缝跟蹤传感器。

• Movement and rational layout of welding seam are the key factors affecting stamping forming quality of welding splice pieces.

  焊缝位置的移动以及布置合理与否是影响拼焊板沖压成形质量的关键。

• The frame grabber can capture 25 frames of welding seam image per second continuously and make it possible to fulfil the real time welding seam image processing and recognition.

  图象采集卡能每秒连续采集25帧焊缝图象，使得实时完成焊缝图象处理与识别成为可能。

• This article discusses how to prevent and lessen welding distortion during welding producing from many aspect such as welding seam length and size, welding form, welding surface size, welding method.

  论述在焊接生产中，如何防止和减少焊接变形，并在焊缝长短、焊缝大小、焊接形式、焊接面大小、焊接方法方面加以探索。

• A welding seam tracking and controlling system has been presented, and abstracting the feature of the seam images.

  分析了视觉传感焊缝跟蹤系统的原理和特点。