片语

water pump seal leakage水泵密封处泄漏

seal oil leakage密封装置漏油

seal plate leakage密封板泄漏

turbocharger shaft seal leakage涡轮增压器轴密封圈泄漏

gas seal[机] 气封

brake piston seal leakage制动器活塞密封泄漏

air seal[机] 气封；气幕；空气隔离层

shaft seal leakage轴封渗漏

gland seal leakage汽封漏汽

hermetic seal leakage密封泄漏

seal drain leakage密封耗损泄漏

英汉例句

• The mechanical seal leakage of hot oil pump has always been an important problem for oil refineries.

  热油泵机械密封的泄漏一直是炼油厂关注的重要问题。

• Therefore, when the mechanical seal leakage test run to exclude inter-shaft seal and cover basically are due to dynamic and static friction ring caused by the destruction.

  因此，试运转机会械密封泄漏在消除轴间及端盖密封失效后，基础上都是由于动、静环摩擦副受损坏所致。

• This equipment is used lamp sealing performance testing, which way is to lamp lumen filled with compressed air, through flow method try leakage instrument measuring its seal leakage detection device.

  该设备是专用于车灯密封性能检测，检测方法是对车灯内腔充入压缩空气，通过流量法试漏仪测量其泄漏量的密封性检测装置。

• The discussion of water injection process to seal leakage occurred in LPG tank was carried out in this article.

  讨论了LPG贮罐发生泄漏事故时采取的注水堵漏工艺。

• No mechanical seal leakage or abnormal vibration or noise occurred to the two pumps during operation.

  两台泵在运转过程中均未见有机械密封泄漏现象发生，也未见有异常的振动和噪声。

• Durable, has no special seal leakage performance characteristics.

  具有经久耐用、特殊轴封毫不泄漏等性能特点。

• Major media, the cause and the approach of static seal leakage were analyzed in FCC plant. Corresponding preventive and treating measures were put forwards.

  分析了催化裂化装置静密封泄漏的主要介质、原因、途径，并提出了相应的预防和治理措施。

• So the IP cylinder efficiency is reducing with the shaft seal leakage increasing.

  随着轴封漏汽量增大，实际中压缸效率降低。

• Note: for mechanical seal, in most cases, due to evaporation from seal leakage of fluid leaking hole in observation, but sometimes a small amount and stable leakage is allowed.

  注意：对于机械密封，在大多数情况下，由于汽化导致从密封泄液孔处观察不到泄漏，但有时少量而又稳定的泄漏是允许的。

• The service of the self-sealed valve in Urea Plant with ammonia technic was introduced, and the cause of the seal leakage was analyzed, the solution of local maintenance was pointed out.

  介绍了自密封阀在氨汽提尿素装置中的应用情况，对其泄漏原因进行了分析；并提出了具体维修方案。

• The Basic structures of finger seal were introduced, and according to the features of finger seal structure, the mathematic model and calculating model of finger seal leakage flow were set up.

  介绍了指尖密封的基本结构，并根据指尖密封的结构特点，提出了指尖密封泄漏流动的数学模型和计算模型。