英汉例句

• objective: to investigate the shear bond strength of three adhesive systems bonded with ceramic brackets to the porcelain surfaces.

  目的：研究三种不同釉质粘接剂对陶瓷托槽与瓷修复体粘接剪切强度的影响。

• mechanical evaluations of a widely adopted coating shear bond strength test standard were conducted via the finite element method.

  本文采用有限单元法对一种普遍采用的涂层剪切结合强度测定标準进行了力学计算。

• the results showed refining has no effect on shear bond strength and wet pressing can improve shear bond strength slightly, the increase of tensile stren…

  提高打浆度和增大湿压对纸页抗张强度的提高主要是纤维相对结合面积增大的结果。

• shear bond strength and the rates of resin fracture were evaluated.

  测定粘接抗剪切强度，并记录去粘接后的树脂面破裂情况。

• methods to test and compare the shear bond strength and the penetration depth of resin tags of fluoride-releasing orthodontic adhesives with those of the traditional orthodontic adhesive.

  方法测试和比较含氟牙釉质粘接剂及不含氟牙釉质粘接剂的剪切强度以及扫描电镜下粘接剂渗入酸蚀后牙釉质表面形成的树脂钉突长度。

• abstr: objective to investigate the influence of different silane coupling agents and different adhesive materials on the shear bond strength of metal brackets bonded to porcelain surface.

  文章摘要：目的研究不同类型硅烷偶联剂和粘接剂对烤瓷瓷面与金属托槽之间抗剪切强度的影响。

• it is concluded in this paper that the effect on the shear bond strength was very small between -40 ℃ and 60 ℃, and the broken shapes were all the broken of concrete;

  研究表明：在-40～60℃之间的温度段内，其抗剪切粘结强度变化较小，破坏形态均为混凝土试块的破坏；

• conclusionthe shear bond strength of the self-made ni-cr-ti porcelain alloys all can satisfy the clinical requirements.

  结论自制镍铬钛烤瓷合金的金瓷结合良好，剪切结合强度可以达到临床应用的要求。

• the shear bond strength was determined and the porcelain fracture rate after debonding was recorded.

  用疲劳实验机检测剪切强度。记录瓷破裂指数。

• the shear bond strength decreased while the concentration of naf was higher than 3%.

  当氟化钠浓度高于3%后，托槽的抗剪粘接强度下降。

• ding hong, wu jian-yong. the vitro study of the influence of different silane coupling agents and adhesive materials on shear bond strength of metal brackets to porcelain surface[j].

  丁宏，吴建勇。不同偶联剂和粘接剂对烤瓷瓷面与金属托槽抗剪切强度影响的体外研究[j]。

• the shear bond strength of circular cfst is great than the square one, and is not considerably affected by the concrete strength.

  圆钢管混凝土界面抗剪粘结强度较方钢管混凝土的大，混凝土强度对圆钢管混凝土界面抗剪粘结强度的影响较小。

• objective to compare the shear bond strength of light cured and chemically cured resin adhesive.

  目的对光固化和化学固化树脂粘接剂的剪切强度进行对比研究。

• the results showed refining has no effect on shear bond strength and wet pressing can improve shear bond strength slightly, the increase oft…

  提高打浆度和增大湿压对纸页抗张强度的提高主要是纤维相对结合面积增大的结果。

• the effect of refining and wet pressing on fiber-fiber shear bond strength and sheet relative bonded area(rba) was investigated with bleached canada kraft softwood pulp.

  实验结果表明，打浆对纤维键合结合强度没有影响，提高湿压对剪切结合强度有增大作用；

• based on the page equation and with the aid of light scattering coefficient technique, a new method to determine fiber-fiber shear bond strength was presented in this paper.

  以page方程为基础，结合光散射系数测量技术，提出了一种测量纤维间剪切结合强度的新方法，并以针叶木为原料，研究了打浆和湿压对纤维剪切结合强度和结合面积的影响。

• based on tests results, the composing of shear bond force, failure mode and the factors of effect on the shear bond strength are analyzed.

  根据试验结果，探讨了钢管混凝土界面抗剪粘结力的组成、抗剪粘结破坏特点以及钢管混凝土界面抗剪粘结强度的主要影响因素。

• type c silane coupling agent can generate the highest shear bond strength between different porcelains and composite resin.

  配方陶瓷偶联剂在瓷与树脂之间产生的粘结强度最高，用于烤瓷或全瓷表面处理均有良好效果。