片语

shear stiffness coefficient剪切刚度系数

effective shear stiffness等效剪切刚度

floor shear stiffness层剪切刚度

Joint shear resistant stiffness节理抗剪切刚度

shear resistant stiffness抗剪刚度

initial segment shear stiffness初始剪切劲度

bearing shear stiffness支座剪切刚度

the shear stiffness剪切刚度

initial shear stiffness初始剪切刚度

英汉例句

• the differential equation, the expressions for bending stiffness and shear stiffness of such space truss, as well as the formulas for calculating internal forces of its members are given.

  文中给出了这类网架结构拟板的基本方程式、弯曲刚度和剪切刚度的表达式以及由拟板内力换算成网架构件内力的一般计算公式。

• the pipeline bridge is built up with triangle sections, its shear stiffness can be derived from the stress diagram for the truss with triangle section.

  在管道跨越工程中，常用三角形截面组合管拱，由三角形截面桁梁的受力分析图，分析推导出其抗剪刚度。

• studying the influence of the shear stiffness on the bridges is always helpful to the bridge seismic resistance design.

  研究它们在减震中的作用对抗震设计很有指导意义。

• this method can be used in other shear stiffness calculations for straight line truss.

  所述分析方法可推广到其它直线桁梁的抗剪刚度的计算。

• it is demonstrated that there is a decrease in the peak shear strength and an increase in the shear stiffness when the shearing velocity increase.

  实验结果表明：试样的峰值剪切强度随着剪切速率的增大有减小的趋势，随着剪切速率的增大减小的幅度变小；

• in this paper, a new material and a new concept are used, thus the compression stiffness and longitudinal shear stiffness can keep fairly low while the lateral shear stiffness increases greatly.

  采用一种新材料和新概念，较好地解决了在大幅度提高支座横向抗剪刚度的同时，仍保留抗压和纵向抗剪刚度较低的有利特性。

• by way of the shake table test for the model of continuous\|beam bridge, the results of the influence of the damp, pier height and bearing shear stiffness on the model and piers is researched.

  通过连续梁桥模型振动台试验 ，分析了阻尼、墩高、支撑剪切刚度对模型梁和墩减震性能的影响。

• the demands of strength for steel bars are presented. the effects of tension and compression stiffness for steel bars on the loss factor and shear stiffness of viscoelastic damper are a…

  同时分析了支撑中钢桿拉压刚度对黏弹性阻尼器损耗因子和抗剪刚度的影响，并在此基础上给出了考虑钢桿拉压刚度影响的消能支撑水平控制力表达式；

• elastic-plastic solution for axially loaded single pile considering variation of shear stiffness coefficient;

  根据计算的应变结果，提出了一种定义剪切区形状的方法。

• this kind of element can make use of joint experiment data to build solid joint model and can include normal nonlinear stiffness and coupling between shear stiffness and normal pressure.

  该单元能够利用现有的结合部实验数据建立实体模型，能够计及法向的非线性刚度和剪切刚度与法向面压的祸合关系。

• an approach to determining normal stiffness and shear stiffness of fracture zone is also discussed in the paper.

  文中还探讨了断裂带法向刚度和切向刚度的计算方法。

• this paper presents two calculation methods for determining transverse shear stiffness coefficients: weight function method and strain energy method.

  本文研究了十字叠层板横向剪切刚度系数的计算方法。

• if we let the transverse shear stiffness approach to infinity, the governing equation of refined theory can be reduced to the classical thin shell equation.

  当壳体的横向剪切刚度很大时，证明了本文提出的精化理论同经典理论的一致性。

• the analysis also shows that joint anchored by inclined bolt has greater shear stiffness than that anchored by bolt perpendicular to joint.

  分析表明，高的巖石单轴抗压强度、较大的锚固面积比有助于提高锚固节理的剪切刚度。

• this paper draws the conclusion that as long as the laminate area proportion reaches more than 27%, and laminate area is roughed quite well, the shear stiffness can be guaranteed.

  结论只要叠合接触比例在27%以上，叠合接触面经有效粗糙处理和配筋，就能保证叠合接触面的抗剪刚度。