英语释义

1. slipband

片语

slip the line倒绳

slip-line filed滑移线

generalized slip-line广义滑移线

slide wire[电] 滑线

slip casting line注浆流水线

slip-line methods滑动线分析法

slip-line field滑移线场

slip-line technique滑移线法

slip-line method滑移线解

slip work line倒大绳

英汉例句

• fourth, according to the plasticity theory and slip line theory, establish the contact pressure model between the single grain (simulative) and the die surface, and test the feasibility of the model.

  然后，以塑性力学、滑移线理论为依据，建立单磨粒（模拟）与模具表面的附着力模型并进行试验验证。

• the paper analyzes the limited load of wedge by unified strength theory, finds its solution in slip line and discusses its application in geotechnical engineering.

  采用统一强度理论对楔体进行了极限分析，得到了极限荷载的滑移线解，并讨论了其在巖土工程中的应用。

• slip line and if the use of spare parts of the site does not meet, neither spare taifen and heat exchange equipment, cannot stop again, should be the scene of the concise and disposal.

  滑线若是运用现场没有满足的备件，而换热设备既无备用台份，又不能停机时，应进行现场的简洁处置。

• the slip line based mold element with the mold element principle and method is the key research work.

  本文以已提出的模型元分析法为理论依据，研究其基本原理和应用；

• the deforming force of cone-die direct extrusion is solved by a mathematic method based on the simplified flow model of slip line field.

  基于滑移线场的简化流动模型，运用数学方法求解出了一种锥形模正挤压变形力的最佳上限解，并将该上限解用通用解析式表达出来。

• at the present time, there are mainly three theoretical methods to determine the ultimate bearing capacity of soil foundation:limit equilibrium method, slip line method and limit analysis.

  目前巖土工程界确定地基极限承载力的理论方法主要有：极限平衡法，滑移线法以及极限分析法。

• the application of the characteristics is explained in an example of constructing a slip line field.

  以一个滑移线场构造为例，说明了某些性质的应用。

• furthermore, from the analytical results indicate that the shear band mode of discontinuous bifurcation is essentially identical with slip line in the plane strain condition.

  进一步分析表明，对于平面应变情形，剪切带同滑移线本质上是一致的。

• the global safety factors were calculated by the stress integration along a slip line and a concept of 「small slip failure」 was introduced in stability of the embankment slope.

  通过在边坡滑弧上进行线积分，得出边坡在不同时刻的整体安全系数，进而提出了路堤边坡降雨作用下「小弧滑动」的概念。

• in this paper some problems existing in the slip line field theory and the upper bound method based on the associated flow rule were analyzed.

  而试验得知，巖土材料并不服从关联流动法则，因而应力特征线与速度滑移线不可能重合。

• the basic theoretical methods such as slab method, ubet, slip line method, fem, and fvm have been used in the research of metal plastic forming technology.

  研究金属塑性成形规律的理论方法现在有主应力法、上限法、滑移线法、有限元法和有限体积法。

• with the aid of the method of finite differences, we get the slip line field around a shaft, and analysed the law of the development of shaft-earth-pressure.

  并借助有限差分法求解竖井周围的滑移线场，分析了竖井（地）压的作用与变化规律。

• slip line is a kind of surface defect which occurs in the forming of automobile panel and affects surface quality of automobile panel and appearance of body.

  滑移线是汽车覆盖件沖压生产中经常出现的一种表面缺陷，它严重影响了覆盖件的表面质量和车身的外观。

• from the stereographic plots of the slip line directions measured around the specimen surface, the slip planes were determined.

  根据试样表面滑移线的方向，在极图上确定滑移面。

• the unit pressure in backward extruding hollow billet has been calculated by the slip line method and the upper bound method.

  本文对空心件反挤的单位挤压力，采用滑移线法和上限法进行了计算。

• because of the rational design and optimization of the upper bound flow mode, the upper bound solution is only 2% above the slip line soltition.

  由于上限流动模型设计合理并进行优化，取得了上限解仅高于滑移线解2%较好结果。

• the reason causing oscillatory was analyzed by applying concerned slip line field theory.

  同时应用滑移线有关理论知识对其摆动的原因进行了分析。

• on the basis of above experiment, fracture mechanism of x60 over-heated haz was given using the theory of slip line field.

  在上述实验结果的基础上，采用塑性滑移线场理论，提出了x60过热区在不同服役温度下的断裂机理。

• based on the theory of slip line and plastic deformation of metal, the clamping force for forging reduction of cylinder is analyzed and studied.

  应用滑移线理论和金属的塑性变形理论，分析研究圆柱体镦粗过程中的夹紧力的计算方法，并与试验结果进行比较。

• the mechanism, assorting, setting method of slip line are discussed in detail. it can provide reference to prevent the occurrence of slip line.

  对滑移线的产生机理、分类及其解决方法进行了全面的研究，为汽车覆盖件沖压生产时出现滑移线和维修提供了参考。

• a study of the literature in oblique cutting shows that only chip formation and mechanics have been studied to some extent. even these are based on single slip line concept.

  从文献看到的斜角切削研究报告大多数限于切屑的形式及基于单剪切面概念的力学研究，似乎斜角切削的研究远远不如直角切削深入。