片语

stress s distribution应力分布

internal stress distribution内应力分布

ground stress field distribution地应力场分布

vertical stress distribution纵向应力分布

plastic stress distribution弹塑性应力分布

secondary stress distribution二次应力分布

stress gradient distribution应力梯度分布

stress great distribution应力重分布

stress field distribution应力场分布

英汉例句

• The computed results show that the presence of an interphase can have an important influence on the effective property and local stress distribution of the composites.

  还将上述方法与均匀界面层模型进行了比较，计算结果表明，界面层的性质对复合材料有效性质和局部应力的分布有着重要影响。

• The whole bond slip curve and bond stress distribution along embedded length were measured by continuous automatic collection.

  采用了连续自动的采集方式，测出了较完整的粘结滑移曲线以及粘结应力沿埋长的分布。

• Finally it analyses stress distribution of the jaw.

  最后分析了抓爪的应力分布。

• For the plates with finite dimensions, the finite element method is used to obtain the stress distribution and stress concentration around the ovaloid opening.

  对于有限尺寸板内开孔的情形，文中用有限单元法来分析腰圆形孔口的应力分布和应力集中。

• The stress distribution curve can be obtained directly by a pen recorder with a given scaling.

  被测玻璃应力的分布曲线可以直接用记录仪记录。

• Therefore, it is not stress distribution in certain even section but integrate stress flow inside the cap that should be considered.

  因此，在厚承台设计时应考虑承台内部的完整应力流，而不是某一平截面上的应力分布。

• The last two factors induce borehole instability both by affecting stress distribution around wellbore and material properties of rock.

  但后两者都是影响井壁应力分布和巖石力学性能而造成井壁不稳定。

• By this method, it researches the stress distribution of plane problem for a tooth on synchronous belt.

  用此方法对梯形齿同步带一个齿上的平面问题的应力分布进行了有限元分析研究。

• Subsequently, the high stress areas and the stress distribution of the joint have been found out by handling and analyzing the large quantity data.

  然后，根据试验结果得到的大量数据，经分析找出节点环板的高应力区及其大致的应力分布情况。

• This article has made an photoelastic study of the influences of geological structure on the stress distribution of wall rocks and an estimate of the rational range of reinforcement.

  本文介绍了用光弹法讲究地质构造对洞室应力分布的影响，预估围巖的合理加固范围。

• The finite element analysis showed that the normal stress distribution of the grillage wall was about the same as that of the solid wall.

  有限元计算表明，网格墻在轴力和水平力作用下的正应力分布与实体墻总体上一致；

• It is shown that the characteristics of shear stress acting on bolt vary in different zones zone of surrounding rock and are reflected in the axial stress distribution of bolt.

  结果表明，在围巖不同区内，锚桿所受剪切力具有不同的特点，而且，锚桿所受剪切的特点在锚桿轴力分布中得到了反映。

• Different from photoelastic method, acoustoelastic method does not need transparent model and can measure stress distribution of material directly.

  与光弹性方法不同的是声弹性方法不需要透明模型，能直接测量材料的应力分布。

• The stress characteristic of the interface, deformation rule under the action of load and the stress distribution rule were discussed by adopting the experimental research method.

  采用实验研究的方法，探讨锚固体界面力学特征、在荷载作用下变形规律以及界面上的应力分布规律。

• The finite element method is used to study the internal stress distribution condition of the KE495 engine crankshaft, then the unreasonable design of the original crankshaft is known.

  利用有限元法分析KE495发动机曲轴的内部应力分布状态，得出原曲轴结构的不合理之处。

• Introduces geological formation for building nature gas storage. Sets forth the rock body for storage building, its major structural face distribution and ground stress distribution behavior.

  介绍了建设天然气地下储库的地质基础，阐述了建库的巖体其主要结构面分布及地应力分布特征。

• The thermal stress distribution of the stainless steel lined composite steel pipe prepared by centrifugal-SHS process was calculated by the finite element method under thermoelastic assumption.

  用有限元方法计算了铝热离心法制备不锈钢内衬复合钢管过程中的残余热应力分布。

• This paper discusses the common problems in the design of frame calculation sketch and stress distribution at corner of the jetted plate.

  本文试对框架的计算简图和悬挑板转角处应力分布两个设计中常见的问题作一探讨。

• The result of an engineering example shows that solution is effective and convergence is stable, and stress distribution of dam body tends to uniformity after optimization.

  计算实例表明，该方法求解效率高，结果的收敛性稳定，优化后的坝体应力分布更趋于均匀。

• Through a large amount of calculation, the stress distribution Pattern of beam axle is obtained for some main load cases.

  通过大量计算，对应于几种主要的载荷工况，得到了车桥横梁的应力分布规律。

• Journal center orbit, oil film pressure and stress distribution on alloy has been got by lubricating calculation.

  通过润滑计算得到轴心轨迹、油膜压力和合金层应力分布，对轴瓦失效过程进行了分析。

• The expressions of load, displacement, stress and residual stress distribution for hole cold_extrusion process are established by using elastic_plastic theory.

  利用弹塑性理论建立了孔冷挤压的载荷、位移、应力以及残余应力分布表达式；

• The geotechnical anchoring theory is an important part of anchoring technology and the stress distribution of anchorage body is one of the core contents of anchoring theory.

  巖土工程锚固理论是锚固技术应用与发展的重要组成部分，而锚固体的应力分布又是锚固理论的核心内容之一。

• The more attention was paid for the effects of matrix, interface and fiber orientation on stress transfer and stress distribution in composite.

  研究中主要讨论了基体、纤维和界面的力学性能以及纤维位向的变化对应力传递和应力分布的影响。