片语

boot third device解雇第三个设备

Second Boot Device第二启动设备

boot othet device可自其它装置开机

Boot Other Device其它启动设备

Select Boot first device设置第一设备

boot display device引导显示设备

Boot The Device启动该设备

Boot Device Configuration引导设备配置

nd Boot Device同上

proper boot device正确的引导装置

英汉例句

• the bios loads the first sector of the boot device and executes the code it contains.

  bios加载启动设备的第一个扇区并运行其包含的代码。

• (if you will need this option later, define the third boot device as network bootp).

  （如果您以后还需要这个选项，那么将第三引导设备定义为networkbootp）。

• a boot device can be a floppy disk, a cd-rom, a partition on a hard disk, a device on the network, or even a usb flash memory stick.

  引导设备可以是软盘、cd-rom、硬盘上的某个分区、网络上的某个设备，甚至是usb闪存。

• now, you need to select the boot device on which to install linux.

  现在，需要选择根设备安装linux。

• you can optimize the process of determining the boot device by selecting the device from which you'll most commonly boot (typically, the hard disk).

  通过选择最经常引导的设备（通常是硬盘）可以优化确定引导设备的过程。

• operator notes: the boot device should be preceded by checking whether the coupling nut loose or fall off, if in time to tighten the nut with the wrench.

  操作工须知：在启动设备前应先检查联轴器的螺母是否有松动或脱落，如有要及时将螺母用扳手把紧。

• when a boot device is found, the linux kernel boot process begins.

  找到引导设备后，开始linux内核引导过程。

• at this stage, you need to set up the boot device in the qlogic bios.

  在该阶段，您需要在qlogicbios 中设置根设备。

• to boot using the ibm installation toolkit live dvd, make sure your system has the cd/dvd-rom drive or the network adaptor as its first boot device as follows

  要使用ibminstallationtoolkitlivedvd引导机器，请确保您的系统使用cd/dvd-rom驱动器或网络适配器作为其第一引导设备，方法如下

• set up hba to enable the bios and select the boot device from ds8000.

  将hba设置为支持bios，并选择从ds8000启动设备。

• the server will need to be rebooted after the update process, so make sure the bootlist is showing the target alternate disk as the first boot device (as seen in listing 7).

  服务器需要在更新过程完成后重新启动，所以要保证启动列表显示目标备用磁盘作为启动设备（如清单7 所示）。

• on some systems, you must press a function key to select the boot device or adjust a basic input/output system (bios) option to boot from the optical drive rather than from your hard disk.

  在有些系统上，您必须按一个功能键来选择引导设备，或者调整一个基本输入/输出系统（bios）选项来从光驱引导，而不从硬盘引导。

• press any key to restart reboot and select proper boot device or insert…

  不是，这个提示的意思是：按任意一个键重启你的电脑，或者选择合适的设备…

• the method for setting up boot devices and selecting a boot device at startup is specific to your system and its bios.

  设置引导设备和选择在启动时引导设备的方法特定于您的系统及其bios。

• your boot device is the cartridge disk controller (dp), which you associate with the external file from the software kit (iu6_dp0.dsk).

  引导设备是盒式磁盘控制器 (dp)，您可以将其与来自软件工具包的外部文件 (iu6_dp0.dsk) 关联。