英语释义

• a hollow cast-iron cylinder attached to the wheel that forms part of the brakes

片语

brake e drum boring machine制动鼓镗床

Front caliper-brake rear drum brake前钳闸后抱闸

brake-drum glaze盘式制动器

brake e drum lathe制动鼓车床

friction brake-drum翻译

Brake e Drum闸鼓

Front V-brake rear drum-brake前V

英汉例句

• can be customized according to customer request processing special filters, brake drum (the need for samples) if necessary please contact us.

  可根据客户要求加工定做特种滤清器、剎车鼓（需提供样品）如有需要请与我们联系。

• therefore, it is necessary to study the application of vanadium-titanium vermicular cast iron in ingot mould, glass mold, auto brake drum and brake disc using abundant v-ti iron in china.

  因此，利用我国丰富的钒钛生铁资源，开展钒钛蠕墨铸铁在钢锭模、玻璃模具以及汽车剎车鼓和列车制动盘等方面的应用研究很有必要。

• brake drum is a key component and damageable part in motor vehicle brake system.

  汽车制动鼓是汽车制动系的基础件和易损件。

• with increase of automobile's load and speed, it is stressed that material of brake drum has been developing and has high strength, anti-fatigue, good hardness.

  随着汽车载重和速度的增加，使得所需要的制动鼓材料应当发展同时具有高强度、高抗热疲劳性和良好的硬度。

• drawing process for shaping the brake drum oil shield of truck ca151 has been deliberated.

  对ca151型汽车制动鼓挡油盘拉延成型工艺进行了探讨。

• whichever method is used, and finally the need to brake drum brake shoe and the contact area for more than 70%.

  无论采用哪种方法，最后必须使制动鼓与制动蹄的接触面积达到70%以上。

• the brake drum is closely sleeved on an electric engine spindle;

  剎车鼓紧密的套设在电机主轴上。

• if not a flat, should check the brake pedal free trip or brake drum brake friction clearance.

  如果没有一个平稳的，应检查剎车踏板免费旅行或剎车片摩擦制动鼓间隙。

• optimum selection of the technological parameters of plasma spraying and field tests show that spraying cowc35 wear-resistant coating on the surface ofdrawworks brake drum is preferable.

  等离子喷涂工艺参数的优选和试验研究的初步结果表明，在绞车剎车鼓表面喷涂cowc35耐磨硬质合金涂层的工艺是可行的。

• the foundry method of a super - heavy truck brake drum to which there is strict technical requirements was briefly introduced.

  简介技术要求极其严格的特大型汽车制动鼓的铸造生产工艺及铸造缺陷的防止措施。

• a spring attached to each brake shoe returns it also to its original position, free of the brake drum .

  附接在各个制动蹄上的弹簧也将制动蹄拉回原位，不与鼓轮接触。

• large supply lada, moscow, volga and other russian cars brake drum brakes.

  大量拉达，伏尔加，莫斯科人等俄罗斯车系剎车盘，剎车鼓。

• with the increase of payload capacity and speed of automobiles, it is required that brake drum material should have high strength, high thermal fatigue resistance and high hardness.

  随着汽车载重和速度的增加，使得所需要的制动鼓材料应当发展成同时具有高强度、高抗热疲劳性和良好的硬度。

• the sizes and distribution of residual stresses in 120 brake drum are useful to design brake drum of the automobiles and select manufacture craft of large castings.

  得出了120制动鼓铸件残余应力大小及分布规律，为设计汽车制动鼓及大型铸件制造工艺提供了依据。

• brake problems brake shoe and the gap between the brake drum is too small, temperature brake drum, trailer brake easily cause stagnation, such as fault locked;

  制动不灵制动蹄片与制动鼓之间的间隙过小，制动鼓温度升高，易引起制动拖滞、抱死等故障；

• if the normal, high-speed friction film and brake drum clearance.

  若正常，可高速磨擦片与制动鼓间隙。

• under given radius and width of the brake drum and thrust of actuating pump, braking performance may be improved by increasing the braking torque of the brake.

  在制动鼓半径、制动鼓宽度和制动分泵推力一定的情况下，增大制动器的制动力矩，即可提高制动性能。

• with the help of the results calculated by electronic computer, the temperature curves of brake drum friction surface, represented by the model 130-2 rig, are set up.

  借助电子计算机的计算结果并绘制了以130—2型石油鉆机为代表的重型鉆机剎车鼓摩擦表面的温度曲线。