片语

gear engagement[机] 齿轮啮合，[机] 齿轮齿啮合

gear s in mesh啮合的齿轮

gear mesh stiffness齿轮啮合刚度

tight gear mesh齿轮紧啮合

gear mesh transfer matrix齿轮啮合传递矩阵

Gear-mesh Frequency啮合频率

gear mesh theory齿轮啮合理论

micro gear mesh微齿轮啮合

gear mesh efficiency齿轮啮合效率

gear mesh error啮合齿向误差

英汉例句

• The motor position is adjustable to accommodate different gears and to allow adjustment of the gear mesh between the pinion and its mating spur gear.

  电机的位置是可调节的，以适应不同的齿轮，并允许该小齿轮及其配对正齿轮之间的调整的齿轮的啮合。

• It features in matching backing triad contrate gear mesh positioning spiral lifting locking good rigidity internal uplift reliable structure flexible operating mode and long service life.

  采用对销反靠，三联端面齿盘啮合定位，螺旋升降锁紧，刚性好，内抬起，结构可靠，工作灵活，使用寿命长。

• With increase in defect severity, not only the defective gear mesh frequency gains energy, but also large impact energy appears in low-frequency regions.

  与增加的缺陷的严重性，不仅有缺陷齿轮啮合频率增益能源，并且还大的影响，能源出当前低频区。

• A calculation method and corresponding formulas are presented by using Hertz contact theory and gear mesh theory.

  应用赫兹理论和齿轮啮合理论给出了螺旋齿轮齿面接触应力的计算方法和相关公式。

• The nonlinear gear mesh force and nonlinear oil film force were considered synchronously, the dynamic model of geared rotor-oil journal bearing system was proposed.

  同时考虑非线性齿轮啮合力和非线性油膜力的影响，建立齿轮-转子-滑动轴承系统的动力学模型。

• Through design and calculation, determined soft and rigid gear conjugation coefficient, obtained teeth side clearance when soft and rigid gear mesh transmission.

  通过设计计算确定了柔、刚轮的变位系数，得到了柔、刚轮在啮合传动时的齿侧间隙值。

• With increase in defect severity, energy is distributed to the sidebands of the gear mesh frequency across supply line frequency.

  与增加的缺损严重，能源是分配给边的齿轮啮合频率跨越供电线路的频率。

• Under the precondition of an absence of increase in gear mesh error a rational support parallelism can be set.

  在不增加啮合齿向误差的前提下，合理给定支承平行度要求。

• This paper describes the construction and working principle of a relay-type synchro-self-shifting clutch with some problems involved in gear mesh process and design approach being also discussed.

  本文主要介绍了中继式自动同步离合器结构，并论述了其啮合过程及设计中的几个问题。

• This paper discuses the phenomenon by lost stability of gearing parameters in considering the gear mesh stiffness, and put forward a criterion of lost stability of gearing parameters.

  探讨了由于啮合刚度周期性变化引起的啮合参数失稳现象，得出了相应的啮合参数失稳判据。

• The internal teeth of the ring gear mesh with the planet gear teeth. Thus, the ring gear rotates with the other parts of the planetary gear system.

  内齿圈的内齿与行星轮的齿啮合。因此，内齿圈随着行星轮系统的其他配件旋转。