英语释义

1. the resultant moment about the neutral axis of any cross section of a rod or beam of the system of forces that produce bending

片语

bending g moment arm弯曲力臂

flexural moment弯矩，挠曲力矩

bending hysteresis moment弯曲滞后矩

bending g moment弯矩

bending bending moment弯矩增值

bending-moment curves弯矩曲线

bending g moment diagram弯矩图

bending g moment coefficients弯矩系数

bending g moment density弯矩密度

Bending-moment equation弯矩方程

英汉例句

• the paper discusses how to regulate the amplitude of bending moment within beam end for frame structure, and presents revisal suggestions for previous designs.

  对框架结构梁端弯矩应如何调幅问题做一探讨，对以往设计提出修正性的建议。

• based on a new orthogonal cutting model with cutting bending moment, a theoretical calculation method of the cutting bending moment is put forward.

  根据带弯矩的正交切削新模型，提出了切削弯矩的理论预报方法。

• this paper deals with the mechanical behaviors of steel-concrete composite beam and effective width of concrete slab on the axial force and the bending moment together function, based on the past job.

  本文在总结前人工作的基础上，对结合梁斜拉桥中在轴力和弯矩共同作用下的钢—混凝土组合梁截面受力状态和混凝土桥面板有效宽度进行研究。

• but the bending moment at the central hinge must vanish .

  但在中间铰处，弯矩必定为零。

• the actual stress is not proportional to the bending moment .

  实际上应力与弯矩不成正比。

• this paper can satisfy the requirement with steady lateral buckling with the method that scales down the bending moment and abate the space between beams.

  文章通过计算分析，发现可以用支座负弯矩调幅和减小梁间距的办法，满足侧向稳定的要求。

• therefore, the bending moment may cause normal stress at the axis of gravity, and the concept of 「equivalent axial force」 is induced.

  因此弯矩在形心处要引起正应力，从而引出所谓「等效轴力」的概念。

• in this paper, new method on calculation of absolute maximum bending moment and position is introduced, and use influence line to check and compare to tradition method.

  本文介绍了用一种计算梁最不利荷载位置及绝对最大弯矩的新方法，并用影响线进行校核，同时与传统方法进行比较。

• this paper analyses the relativity between bending moment (m) and axial force (n) in calculating ground supporting capacity, and the effect of relativity on reliability calculation.

  分析了在地基承载力验算中，弯矩m与轴力n之间相关性的存在，以及相关性对可靠度计算的影响。

• theoretically analyzing the method and formula which can deduce the moment function of piles by measured bending moment through model tests.

  理论分析由实测弯矩推求桩身弯矩函数的方法，公式。

• experimental results show that the total vertical bending moment can be divided into one low frequent component due to wave loads and one high frequent component due to whipping loads.

  试验数据分析表明，合成弯矩可以分成由波浪载荷引起的低频成分以及由砰击载荷引起的高频成分。

• the basic way that verifies whether bending moment diagram is correct is derivative judge.

  弯矩图是内力图的一种，检验弯矩图正确与否的基本方法是导数的几何意义判定法。

• the amount of immediate correction necessary to nullify the bending moment ranged between 19% and 61% with average 48% (flexible spine model) and 27% (stiff spine model).

  消除弯曲力矩所必需的总即刻矫正率介于19%到61%，平均48% （柔性脊柱模型）和27% （刚性脊柱模型）。

• this paper analyzes the error of torque sensor of strain-resistor which derives from the influences of bending moment on elastic axis , and discusses the eliminating techniques.

  本文对在应用应变式扭矩传感器时由于在弹性轴上的弯矩而引起的误差进行了力学分析，并提出了消除的方法。

• in addition, the failure patterns and ultimate bearing resistance for the square slab with the same ultimate bending moment in two directions are given.

  同时给出两个方向相同极限弯矩的正方形板的破坏图式及极限承载力。

• and for the frame beam end bending moment amplitude modulation factor seems embodiment its value in practice projects.

  框架梁端的弯矩调幅系数的合理取值的价值在实际工程中似乎更能体现出来。

• the results indicate that, the bending moment and displacement of the pile are influenced mainly by the outside load.

  结果表明：荷载大小是影响桩身位移和弯矩的主要因素之一；

• the impact force-time history between the structure and the moving rigid-body, shear force and bending moment distribution along the beams, axial force distribution along the bars were calculated.

  计算了结构与运动刚体之间的沖击力时程曲线、梁中的剪力及弯矩分布、轴力桿件中的轴力分布。