片语

shearing-bonding-strength剪切胶合强度

tensile bonding strength粘接抗张强度

Interface bonding strength界面结合强度

bonding g strength胶合强度

Internal Bonding Strength内结合强度

Bonding Media Strength胶粘介质强度测量

bonding bending strength黏结抗折强度

anchoring strength碇系力；结合强度；锚定强度

英汉例句

• in this study , according to the design of increasing bonding strength between interlayers, phlogopite type calcium mica glass ceramic has been developed .

  研究根据提高云母层间结合强度的构想，研制以钙云母为主相可切削微晶玻璃。

• at surrounding humidity of 90% the ht-730 adhesive still had very high bonding strength and its ageing property and pot life weren , t influenced.

  研制的ht-730胶在环境湿度90 %时仍有很高的粘接强度，同时老化性能和适用期并没有受到影响。

• in this paper, the selection of matrix metals, matrix properties and bonding strength between matrix and bit body are studied.

  研究了电镀薄壁金刚石工程鉆头的胎体金属选择，胎体的性能和胎体与钢休间的结合强度。

• the gradient pps/fep composite anti-corrosive coatings were prepared on carbon steel. the bonding strength of all coating systems was determined by the pull-off test.

  在碳钢表面制备了具有梯度结构的pps/fep复合防腐蚀涂层，采用拉开法测定了各涂层体系的结合强度。

• this gives reason for the high bonding strength of fe deposit in fe-plating without etching.

  由此解释了无刻蚀镀铁层具有高结合强度的原因。

• conclusion:the mao on titanium are favorable to the titanium ceramic bonding strength and treated parameter has a different effect on the titanium ceramic bonding strength.

  结论：钛在烤瓷前经微弧氧化处理有利于钛与瓷的结合，且微弧氧化过程中不同处理参数对钛瓷结合强度有影响。

• the melting state of powder and bonding strength of coating did not vary much within spraying distance in the experiment.

  在试验的喷距范围内，喷距对粉末的熔化状态和涂层结合强度均无明显影响。

• the effect of the experimental parameters on the interfacial bonding strength was investigated, as well as the influences of the anodic oxidation state on the titanium substrate surface appearance.

  研究了试验参数对涂层界面结合强度的影响以及阳极氧化状态参数对钛基体表面形貌的影响；

• it was concluded that the interlaminar tensile strength of the composite is dominated by the bonding strength of the interface between fiber and matrix, not by lay-up orientation.

  结果表明：该复合材料层间拉伸强度较少受到铺层取向的影响，而由纤维与基体的界面结合强度所控制。

• the bonding strength of the new adhesive completely meets the requirements of orthodontic adhesives.

  这种新型粘合剂的粘接强度完全满足了正畸粘合剂的要求。

• the bonding strength between the substrate and the coating was measured by scratch tester.

  采用划痕试验方法测定了涂层与基体之间的结合强度；

• sand blast is the optimum method for surface pretreatment to enhance the bonding strength between coating and matrix.

  喷砂处理是提高涂层与基体结合强度的最佳表面预处理工艺；

• it was revealed by push out test that the hydroxyapatite coating greatly prompt the bonding strength between implant and surrounding hard tissues.

  生物力学实验结果表明，使用羟基磷灰石涂层，可以显着提高骨组织与种植体的界面结合强度。

• objective:this study is to determine the effect of different surface anodizing and degassing-preoxidation on bonding strength of porcelain to ni-cr alloy.

  目的：研究非贵金属合金在上瓷前经过不同的阳极钝化条件处理及除气、预氧化对金瓷结合强度的影响。

• the effects of dosage of each material on the bonding strength were studied.

  研究了原材料的用量变化对胶粘剂粘接强度的影响。

• the bonding strength increases with the increment of temperature and inner-pressure.

  随着温度的升高和压力的增大，两种金属结合强度大大提高；

• the design of different kinds of coatings on titanium alloy was overviewed and some suggestions on how to improve the bonding strength between bioactive ceramic coating and substrate were made.

  本文对钛合金表面不同类型涂层的设计进行了综合评述，并对如何提高生物活性陶瓷涂层与基体的界面结合强度提出建议。

• three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.

  介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。

• a new method for measuring bonding strength between electroplated layer and substrate of diamond tool is proposed.

  提出一种新的电镀金刚石工具镀层与基体结合强度测试方法。

• the influence of rolling-cladding process at different temperatures on initial bonding strength of steel-al clad plate is studied in this paper.

  研究了异温轧制复合工艺制度对钢和铝复合板初结合强度的影响。

• the effects of interfacial diffusion on the microstructure, micro-hardness and interfacial bonding strength of the composite coating materials were analyzed.

  分析了原子扩散对真空熔覆涂层的显微组织、显微硬度以及界面结合强度的影响；